Download

Download Manuals, Datasheets, Software and more:

DOWNLOAD TYPE
MODEL or KEYWORD

Feedback

TekExpress MIPI D-PHY Test Application

DPO-MSO70000 Option DPHY12 and DPHY21, MSO6/6B 6-CMDPHY12 and 6-CMDPHY21

Read Online:

D-PHY or MIPI Display Phy is a standardized physical layer interface for connecting the Camera/Display to the Processor. This interface is predominantly used in mobile devices, infotainment systems and biometric sensors. This is a unidirectional bus with an explicit clock, up to 4 data lanes and consists of High Speed mode and Low Power mode. The High Speed mode is for fast data transfer and Low Power mode is for power saving to extend the battery life. The data flow in a display interface is from processor to the display device and from camera to the processor in the camera interface. The MIPI D-PHY specification testing is done based on the Compliance Test Specification (CTS) and requires a board with dynamic switching of termination between Low Power state and High Speed mode.

The Tektronix TekExpress® D-PHY application offers a complete physical layer test solution for transmitter conformance and characterization as defined in the MIPI D-PHY version 1.2 and version 2.1 specification. The automated test solution along with 70000 C/DX/SX or a 6 Series MSO instruments, provides an easy way to test, debug and characterize the electrical and timing measurements of D-PHY data links.

Key features (version 1.2)

Fully automated solution

  • Performs D-PHY transmitter test with single-button click across High Speed (HS), Low Power (LP), Low Power-High Speed (LP-HS), and Ultra-Low Power State (ULPS) sequences in the D-PHY signal
  • Select individual tests or groups of tests
  • Improved test run time

Eye Diagram Capability

  • Displays the eye diagram of the High Speed signal with option DJA enabled on the scope for Test ID 1.5.4, Data to clock skew test and Test ID 1.5.7 HS-TX Data and Clock Eye Diagram

Image Snapshot

  • Option of including the snapshot of the first reference region of analysis in the captured waveform

100% test coverage as per D-PHY version 1.2, CTS version 1.0

  • Performs fully-automated tests including Bus Turn Around (BTA) and ULPS measurements, as per D-PHY specifications up to version 1.2

Measurement variety

  • D-PHY runs multiple scenarios like Continuous or Burst mode, Termination variations, and varying idle time

Transmitter conformance test and beyond (Debug)

  • Easily modify limits of test parameters in TekExpress for debug, margin, and characterization testing
  • Performs characterization by running TekExpress application in continuous mode to collect data

Signal access

  • Use the low loading, Tektronix TDP7700 (for 6 Series and 6 Series B MSO) or P7700 (for 70000 C/DX/SX Oscilloscopes) Series High Impedance TriMode probe to measure MIPI signals

  • Supports TekFlex™ accessories for flexible probing

Offline and remote analysis

  • Analyze live or pre-acquired waveforms
  • Allows remote execution of tests

Key features (version 2.1)

  • Support Spread Spectrum Clocking enabled / disabled measurements. Triangular Down spreading, deviation 5000ppm at 33 kHz
  • Transmitter eye diagram (Test ID 1.5.7) at data rates > 1.5 Gbps and ≤ 4.5 Gbps measurement using random test pattern of 3 million UI
  • Support Horizontal mask movement. Data eye mask can be moved from center of DDR clock with 0 V crossing up to ±0.1UI range to eliminate data to clock skew effects
  • Support three reference templates (Short, Standard, and Long) for differential insertion loss for data rates > 1.5 Gbps and ≤ 4.5 Gbps
  • Mask prorated to BER 10e-6, with TEYE_TX = 0.53 UI and VDIF_TX 47 mV
  • Option to run tests in Compliance Mode or with user defined settings

Applications

  • Automotive cameras
  • Automotive infotainment and dashboard displays
  • Mobile camera and displays
  • Large tablets
  • Smart watches

Single-button fully automated D-PHY testing

The Tektronix TekExpress D-PHY application runs on 6 Series and 6 Series B MSO with Option 6-WIN installed (Windows 10 operating system) and DPO/MSO 70000 DX/SX Series Oscilloscope. The close integration of the oscilloscope and test software provides an automated, simple, and efficient way to test D-PHY transmitter interfaces and devices consistent to the requirements of the D-PHY Conformance Test Specification version 2.1.

Measurement setup and test execution is simple with the D-PHY software. The intuitive Graphical User Interface (GUI) is laid out to represent the workflow from setup through testing, letting you focus on design and debug instead of setting up the measurements.

D PHY EN US 61W 61487 6
A well-designed workflow-based user interface steps you through test setup and execution.

Simply select tests from the menu for HS, LP, and HS-LP groups as per specifications.

D PHY EN US 61W 61487 6
Select test groups or individual tests from the Test Selection menu.

You can view the schematic of the selected test with a push of a button. You can also display a test connection diagram to avoid setup errors.

Pass/Fail report

The report tab provides a view of the complete test results, pass or fail status, test margin, and images supporting the test results, for each lane of the DUT.

D PHY EN US 61W 61487 6
A detailed report provides a record of test results.
D PHY EN US 61W 61487 6
Eye diagram for Test ID 1.5.4 Data to clock skew test

TDP7700/P7700 series TriMode probes for MIPI D-PHY TX measurements

MIPI D-PHY applications have special probing requirements due to the different signal measurement sources in High Speed and Low Power modes. In High Speed mode, D-PHY signals operate in terminated mode with differential signaling. In Low Power mode, D-PHY signals operate in unterminated mode with single-ended signals. Therefore, MIPI D-PHY has two key probing requirements:

  • Provide a high impedance to minimize signal loading
  • Need both Differential and single-ended mode probing

The Tektronix TDP7700/P7700 Series TriMode probes are designed to meet this measurement challenge. The TDP7700/P7700 work with full AC calibration of the probe and tip's signal path, to provide the highest probe fidelity available for real-time oscilloscopes. The innovative new probe design uses SiGe technology to provide the bandwidth and fidelity needed today and in the future.

D PHY EN US 61W 61487 6
The P7700 Series TriMode probes provide the highest probe fidelity available for real-time oscilloscopes.
D PHY EN US 61W 61487 6
TDP7708 probe with accessories.

A key TDP7700/P7700 connectivity innovation is using solder-down probe tips with the probe's input buffer mounted only a few millimeters from the tip. This approach provides unmatched usability for connecting to MIPI D-PHY circuits.

Other TDP7700/P7700 Series probe characteristics include:

  • An active buffer amplifier on the probe tips with the probe input only 3.2 mm from the buffer.
  • Excellent step response and low insertion loss up to 20 GHz on P7720
  • Low-DUT loading with 100 kΩ (DC) and 0.4 pF (AC) performance
  • High Common-Mode Rejection Ratio (CMRR)
  • Low noise

Specifications

D-PHY specification
Version 1.2 and Version 2.1
D-PHY CTS
Version 1.0
Measurements
Both High Speed and Low Power modes, including ULPS and BTA.
Group 1 tests
Data lane LP-TX signaling
1.1.1
Data lane LP-TX Thevenin output high level voltage (VOH)
1.1.2
Data lane LP-TX Thevenin output low level voltage (VOL)
1.1.3
Data lane rise time
1.1.4
Data lane fall time
1.1.5
Data lane LP-TX slew rate versus CLOAD (δV/δtSR)
1.1.6
Data lane LP-TX pulse width of exclusive-OR clock (TLP-PULSE-TX)
1.1.7
Data lane LP-TX period of exclusive-OR clock (TLP-PER-TX)
Group 2 tests
Clock lane LP-TX signaling
1.2.1
Clock lane LP-TX Thevenin output high level voltage (VOH)
1.2.2
Clock lane LP-TX Thevenin output low level voltage (VOL)
1.2.3
Clock lane rise time
1.2.4
Clock lane fall time
1.2.5
Clock lane LP-TX slew rate vs. CLOAD (δV/δtSR)
Group 3 tests
Data lane HS-TX signaling
1.3.1
Data lane HS entry: data lane TLPX value
1.3.2
Data lane HS entry: THS-PREPARE value
1.3.3
Data lane HS entry: THS-PREPARE + THS-ZERO value
1.3.4
Data lane HS-TX differential voltages (VOD(0), VOD(1))
1.3.5
Data lane HS-TX differential voltage mismatch (ΔVOD)
1.3.6
Data lane HS-TX single ended output high voltages (VOHHS(DP), VOHHS(DN))
1.3.7
Data lane HS-TX common-mode voltages (VCMTX(1), VCMTX(0))
1.3.8
Data lane HS-TX common-mode voltage mismatch (ΔVCMTX(1,0))
1.3.9
Data lane HS-TX dynamic common-level variations between 50-450 MHz (ΔVCMTX(LF))
1.3.10
Data lane HS-TX dynamic common-level variations above 450 MHz (ΔVCMTX(HF))
1.3.11
Data lane HS-TX 20%-80% rise time (tR)
1.3.12
Data lane HS-TX 80%-20% fall time (tR)
1.3.13
Data lane HS exit: THS-TRAIL value
1.3.14
Data lane HS exit: 30%-80% Post-EoT rise time (TREOT) value
1.3.15
Data lane HS exit: TEOT value
1.3.16
Data lane HS exit: THS-EXIT value
Group 4 tests
Clock lane HS-TX signaling
1.4.1
Clock lane HS entry: TLPX value
1.4.2
Clock lane HS entry: TCLK-PREPARE value
1.4.3
Clock lane HS entry: TCLK-PREPARE + TZERO value
1.4.4
Clock lane HS-TX differential voltages (VOD(0), VOD(1))
1.4.5
Clock lane HS-TX differential voltage mismatch (ΔVOD)
1.4.6
Clock lane HS-TX single ended output high voltages (VOHHS(DP), VOHHS(DN))
1.4.7
Clock lane HS-TX common-mode voltages (VCMTX(1), VCMTX(0))
1.4.8
Clock lane HS-TX common-mode voltage mismatch (ΔVCMTX(1,0))
1.4.9
Clock lane HS-TX dynamic common-level variations between 50-450 MHz (ΔVCMTX(LF))
1.4.10
Clock lane HS-TX dynamic common-level variations above 450 MHz (ΔVCMTX(HF))
1.4.11
Clock lane HS-TX 20%-80% rise time (tR)
1.4.12
Clock lane HS-TX 80%-20% fall time (tR)
1.4.13
Clock lane HS exit: TCLK-TRAIL value
1.4.14
Clock lane HS exit: 30%-80% Post-EoT rise time (TREOT) value
1.4.15
Clock lane HS exit: TEOT value
1.4.16
Clock lane HS exit: THS-EXIT value
1.4.17
Clock lane HS clock instantaneous (UIINST)
1.4.18
Clock Lane HS Clock Delta UI (ΔUI)
1.4.19
TX Spread Spectrum Clocking (SSC) Requirements
1.4.20
Clock Lane HS Clock Period Jitter
Group 5 tests
HS-TX Clock-to-Data lane timing
1.5.1
HS entry TCLK-PREValue
1.5.2
HS exit TCLK-POST value
1.5.3
HS clock rising edge alignment to first payload bit
1.5.4
Data-to-Clock skew (TSKEW (TX))
1.5.5
Initial HS Skew Calibration Burst (TSKEWCAL-SYNC, TSKEWCAL)
1.5.6
Periodic HS Skew Calibration Burst (TSKEWCAL-SYNC, TSKEWCAL)
1.5.7
HS-TX Data and Clock Eye Diagram
1.5.8
Alternate Calibration Sequence (TALTCAL-SYNC, TALTCAL)
1.5.9
Preamble Sequence (TPREAMBLE, TEXTSYNC)
1.5.10
Clock and Data Lane TX HS-Idle: THS-IDLE-POST, THS-IDLE-CLKHS0, THS-IDLE-PRE Values
Group 6 tests
LP-TX INIT, ULPS and BTA requirements
1.6.1
INIT: LP-TX initialization period (TINIT, MASTER)
1.6.2
ULPS entry: verification of clock lane LP-TX ULPS support
1.6.3
ULPS exit: transmitted TWAKEUP interval
1.6.4
BTA: TX-Side TTA-GO interval value
1.6.5
BTA: RX-Side TTA-SURE interval value
1.6.6
BTA: RX-Side TTA-GET interval value
Probing configuration
Single-ended and differential acquisition. Conformance requires DP, DN, CP, and CN. One lane is two wires, two single ended probing. In case of continuous clock, a single probe may be used in differential mode.
Multilane
The TekExpress application will perform testing one lane at a time in sequential order, a popup message appears which ask the user to change the physical connection to next data lanes.
Triggering
Edge trigger for clock lane tests in clock continuous mode. Choice of width trigger and transition trigger for all other tests and all other modes .
Reports
CSV, PDF, and MHT formats with images of all acquired waveforms.

Ordering information

Required hardware

Models

D-PHY v1.2D-PHY v2.1
CTS1.01.0
CTS complianceMinimum bandwidth of 8 GHz on oscilloscopeMinimum bandwidth of 13 GHz on oscilloscope
DJA/6-DJAOptional

Test ID 1.5.4 Eye diagram display required DJA. In the absence of DJA, gives the measured value alone.

Mandatory
Oscilloscope modelsMSO/DPO 70000 DXMSO/DPO 70000 DX
DPO/DPS 70000 SX (4 Ch Models)DPO/DPS 70000 SX (4 Ch Models)
MSO/DPO 70000 C (4 GHz and above)
6 Series and 6 Series B MSO (2.5 GHz and above with 6-WIN)6 Series and 6 Series B (2.5 GHz and above with 6-WIN)

Minimum recommended bandwidth on 6 Series and 6 Series B is 4 GHz. However, the application installs on 6 Series and 6 Series B with bandwidth 2.5 GHz

Required software

Options for 6 Series and 6 Series B MSO
Application Option License type
MIPI D-PHY 1.2 Automated Compliance Solution on 6 Series and 6 Series B oscilloscopes. 6-DJA is required for Test ID1.5.4. 6-DJA is optional. 6-CMDPHY New instrument license
SUP6-CMDPHY Upgrade license
SUP6-CMDPHY-FL Floating license
MIPI D-PHY 2.1 Automated Compliance Solution on 6 Series and 6 Series B MSO with 6-DJA enabled. 6-DJA is mandatory 6-CMDPHY21New instrument license
SUP6-CMDPHY21Upgrade license
SUP6-CMDPHY21-FLFloating license
Options for DPO/MSO70000 C/DX/SX Series oscilloscopes
Application Option License type
MIPI D-PHY 1.2 Automated Compliance Solution on 70000 C, DX, and SX oscilloscopes. Opt.DJA is required for Test ID1.5.4. DJA is optionalDPHY12 New instrument license
DPO-UP DPHY12 Upgrade license
DPOFL-DPHY12 Floating license
MIPI D-PHY 2.1 Automated Compliance Solution on 70000 DX and SX oscilloscopes with Opt. DJA enabled. DJA is mandatory DPHY21New instrument license
DPO-UP DPHY21Upgrade license
DPOFL-DPHY21Floating license

Recommended probes

Oscilloscope Probe Quantity
6 Series and 6 Series B MSO TDP7708 Series Tri-mode probe with P77STFLXA solder−in tip with TekFlex connector technology Four (recommended for connecting Dp, Dn, Cp, and Cn)
DPO/MSO70000 C/DX/SX Series P7700 Tri-mode probe with P77STFLXA solder-in tip with TekFlex connector

Recommended test fixtures

Text fixtures Vendor
D-PHY Reference Termination Board UNH-IOL