與我們聯絡

與 Tek 業務代表即時對談。 上班時間:上午 6:00 - 下午 4:30 (太平洋時間)

致電

請致電

與 Tek 業務代表即時對談。 上班時間:上午 8:30 - 下午 5:30 (太平洋時間)

下載

下載手冊、產品規格表、軟體等等:

下載類型
機型或關鍵字

意見回饋

在 2023 年 Tektronix 創新論壇上取得未來工程設計的門票。免費技術研討會。立即註冊。

產品支援和下載

歡迎使用 Tektronix 產品支援

在我們整天與您愉快「討論技術」的時候,我們知道您很著急。所以我們讓您能夠輕鬆地下載所有目前產品和多項已停產產品的手冊、產品規格表和軟體。只要告訴我們您目前所用的產品,我們就會向您呈現所擁有的一切資訊。

您選擇的產品機型目前尚有存貨可供購買。 該產品提供以下支援資訊。

  • 常見問答集 常見問答集 ID
    2450 - Range Compliance: Source limited unexpectedly due to low Measurement Range
    Question: When we try to read the measurements from our 2450 instrument it causes any output voltage to automatically be 1.154 volts into a DMM, which is below the programmed value. Answer:  There is a condition on 24xx series SMUs called ‘range …
    KB-01028
    Sink function doesn't go to zero when not initialized
    Question: I've set my 2450 to sink 100mA. When I enable the load it sinks 100mA, but when I disable the load with blue button in the corner, it still sinks 10mA when the output if off. I want it to go to zero mA load. Answer: The 2450 SMU is a four …
    KB-01047
    Sweep: Can I use an external trigger to stop a SourceMeter sweep?
    Question: Sweep: Can I use an external trigger to stop a SourceMeter sweep? Answer: The SourceMeter trigger model does not have provisions for stopping a sweep using a trigger signal. However, there is a way to accomplish this by using the …
    KB-01468
    Speed: What is NPLC?
    Question: Speed: What is NPLC?   Answer: The Number of Power Line Cycles (NPLC) indicates how long an input signal is integrated to obtain a single measurement. Noise introduced from the power line tends to be periodic. If the A/D converter …
    KB-01485
    Remote Operation: Why do I get a VISA timeout (BFFF0015) using RS-232 with a SourceMeter?
    Question: Why do I get a VISA timeout (BFFF0015) using RS-232 with a SourceMeter?   Answer: When programming a SourceMeter through the VISA layer into RS-232, the use of SCPI commands is required. However, there are additional subtle requirements …
    KB-01460
    Ohms: What is AUTO or MANUAL mode when measuring Resistance with a 2400?
    Question: Ohms: What is AUTO or MANUAL mode when measuring Resistance with a 2400? Answer: What is the difference between Auto and Manual mode for resistance in the Model 2400? The AUTO resistance measuring mode of the Model 2400 configures the unit …
    KB-01492
    How do I create an I-V Characterizer test that uses more than one SMU Instrument?
    Question: How do I create an I-V Characterizer test that uses more than one SMU Instrument? Answer: Use the “Instruments” button in the I-V Characterizer app toolbar to access the “Add Channels” button to add more SMU instruments to your test.   You …
    KB-01364