연락처

텍트로닉스 담당자와 실시간 상담 6:00am-4:30pm PST에 이용 가능

전화

전화 문의

9:00am-6:00PM KST에 이용 가능

다운로드

매뉴얼, 데이터 시트, 소프트웨어 등을 다운로드할 수 있습니다.

다운로드 유형
모델 또는 키워드

피드백

제품 지원 및 다운로드

텍트로닉스 제품 지원 센터

'텍크놀로지(Tek-nology)'를 개발하는 일은 행복하지만, 동시에 매우 바쁘다는 걸 알고 있습니다. 이에. 텍트로닉스는 현재 출시되는 모든 제품과 단종된 여러 제품에 대한 설명서와 데이터 시트, 소프트웨어를 쉽게 다운로드할 수 있도록 제품 지원 센터를 만들었습니다. 사용 중인 제품명을 입력해 주시기만 하면 텍스로닉스가 보유하고 있는 모든 정보를 알려 드리겠습니다.

선택한 제품 모델은 현재 구입할 수 있으며, 다음 지원 정보도 제공됩니다.

  • FAQ FAQ ID
    Sink function doesn't go to zero when not initialized
    Question: I've set my 2450 to sink 100mA. When I enable the load it sinks 100mA, but when I disable the load with blue button in the corner, it still sinks 10mA when the output if off. I want it to go to zero mA load. Answer: The 2450 SMU is a four …
    KB-01047
    Sweep: Can I use an external trigger to stop a SourceMeter sweep?
    Question: Sweep: Can I use an external trigger to stop a SourceMeter sweep? Answer: The SourceMeter trigger model does not have provisions for stopping a sweep using a trigger signal. However, there is a way to accomplish this by using the …
    KB-01468
    Speed: What is NPLC?
    Question: Speed: What is NPLC?   Answer: The Number of Power Line Cycles (NPLC) indicates how long an input signal is integrated to obtain a single measurement. Noise introduced from the power line tends to be periodic. If the A/D converter …
    KB-01485
    Remote Operation: Why do I get a VISA timeout (BFFF0015) using RS-232 with a SourceMeter?
    Question: Why do I get a VISA timeout (BFFF0015) using RS-232 with a SourceMeter?   Answer: When programming a SourceMeter through the VISA layer into RS-232, the use of SCPI commands is required. However, there are additional subtle requirements …
    KB-01460
    2450 - Range Compliance: Source limited unexpectedly due to low Measurement Range
    Question: When we try to read the measurements from our 2450 instrument it causes any output voltage to automatically be 1.154 volts into a DMM, which is below the programmed value. Answer:  There is a condition on 24xx series SMUs called ‘range …
    KB-01028
    Ohms: What is AUTO or MANUAL mode when measuring Resistance with a 2400?
    Question: Ohms: What is AUTO or MANUAL mode when measuring Resistance with a 2400? Answer: What is the difference between Auto and Manual mode for resistance in the Model 2400? The AUTO resistance measuring mode of the Model 2400 configures the unit …
    KB-01492
    How do I create an I-V Characterizer test that uses more than one SMU Instrument?
    Question: How do I create an I-V Characterizer test that uses more than one SMU Instrument? Answer: Use the “Instruments” button in the I-V Characterizer app toolbar to access the “Add Channels” button to add more SMU instruments to your test.   You …
    KB-01364