RM5 Rackmount Kit Instructions

Rackmount Kit for 5/6 Series MSO

This document supports installing Tektronix 5/6 Series instruments in a rackmount kit to fit in a standard 19-inch equipment rack.

此手冊適用於:

MSO56, MSO58, MSO64, MSO64B, MSO66B, MSO68B, MSO54B, MSO56B, MSO58B, RM5

手冊下載協議

注意：從此網站下載任何文件前，請先詳閱下列條款與條件。若從 Tektronix 網站下載手冊，即表示您同意下列條款與條件：

目前支援之產品的手冊：

Tektronix 在此授予 Tektronix 儀器擁有人權限與授權，可在此網站下載和重製手冊，供內部或個人使用。未經 Tektronix, Inc 特別書面授權，不得重製目前支援的產品手冊，並散佈給他人。

Tektronix 手冊可能經適當修訂，以反映製造過程中對產品所做的變更。因此，任何現有產品可能具備不同版本的手冊。請務必確保使用者取得特定產品序號的正確手冊版本。

不再支援之產品的手冊：

Tektronix 不提供已不再長期支援的量測產品手冊。 Tektronix 於此授權其他人重製和散佈任何 Tektronix 量測產品手冊副本的權限與授權，包括使用者手冊、操作員手冊、維修手冊等，該等手冊應 (a) 具備 Tektronix 零件編號，且 (b) 為 Tektronix 不再支援的量測產品手冊。

此等權限與授權不適用於 Tektronix 目前仍支援的任何手冊或其他出版品，或視訊生產產品/彩色印表機產品的任何手冊或其他出版品。

免責聲明：

若量測產品手冊或其他出版品並非 Tektronix 提供，或並非依前述權限和授權製作或散佈，Tektronix 將不保證其資訊、文字、圖片、示意圖、零件清單或其他內含資料的準確度或完整性。

Tektronix 得逕行變更此網站內容或其產品，恕不另行通知。

責任限制：

若因使用依前述權限和授權製作或散佈的任何量測產品手冊或其他出版品，而導致任何損害 (包括但不限於：任何二次損壞或意外損壞、利益損失損害、營業中斷損害或違反智慧財產權損害)，Tektronix 概不負責。

Read Online

RM5 Rackmount Kit Instructions

Important safety information

This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe condition.

To safely perform service on this product, see the Service safety summary that follows the General safety summary.

Service safety summary

The Service safety summary section contains additional information required to safely perform service on the product. Only qualified personnel should perform service procedures. Read this Service safety summary and the General safety summary before performing any service procedures.

To avoid electric shock

Do not touch exposed connections.

Do not service alone

Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is present.

Disconnect power

To avoid electric shock, switch off the product power and disconnect the power cord from the mains power before removing any covers or panels, or opening the case for servicing.

Use care when servicing with power on

Dangerous voltages or currents may exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.

Verify safety after repair

Always recheck ground continuity and mains dielectric strength after performing a repair.

Kit description

The rackmount kit is a collection of parts that, once installed, configure the instrument for mounting into a standard 19-inch equipment rack. This rackmount kit supports all 5 Series MSO (except 5 Series MSO Low Profile) and 6 Series MSO instruments.

Minimum tool and equipment list


Required tools and equipment	Part number
Screwdriver, Phillips, #2	Standard tool
Screwdriver, T-10 Torx	Standard tool
Screwdriver, T-15 Torx	Standard tool
Screwdriver, T-8 Torx	Standard tool

Kit parts list

The following table lists the parts for the kit; not all of the parts will be needed for your instrument setup.


Item	Quantity	Part number	Description
-----	1 each	071-3523-XX	RM5 RACK MOUNT KIT INSTRUCTIONS
-----	1 each	644-1088-XX	RACKMOUNT KIT CONSISTING OF THE FOLLOWING ITEMS:
1	1	407-5871-XX	BRACKET, ASSEMBLY, LEFT, SAFETY CONTROLLED
2	1	407-5872-XX	BRACKET, ASSEMBLY, RIGHT RACK KIT, SAFETY CONTROLLED
3, 4	2	407-5870-XX	BRACKET, BOTTOM RACKMOUNT KIT, SAFETY CONTROLLED
5	1	016-2114-XX	This kit includes the hardware required to assemble the rackmount kit and attach it to the instrument.
	016-2114-XX KIT, HARDWARE RACKMOUNT KIT CONSISTING OF THE FOLLOWING ITEMS:
	12	211-1584-XX	SCREW, MACHINE, M3X0.5X6MM PAN HEAD, TORX T10
	18	211-1653-XX	SCREW, M4 X 0.7 X 12 PAN HEAD, TORX T15
	2	367-0525-XX	HANDLE, CARRYING
	4	212-0278-XX	SCREW, MACHINE; 10-32 X 0.5, FLH, 100 DEG,STL CD PL, POZ
6	1	016-2116-XX	This kit includes the hardware required to mount the assembled instrument and rack kit to the instrument rack.
	016-2116-XX KIT, HARDWARE RACKMOUNT KIT CONSISTING OF THE FOLLOWING ITEMS:
	14	210-0833-XX	WASHER, RECESSED; 0.42 ID X 0.112 THK, STL NI PLATED, 0.588 OD
	14	210-1061-XX	WASHER, FLAT; 0.203 ID X 0.625 OD X 0.062, ZINC PLATED STEEL
	14	210-1548-XX	WASHER, FLAT 12 OD X 6.4 ID X 1.6THK
	14	211-1218-XX	SCREW, M6 X 16MM OVAL HEAD, PHILLIPS
	14	211-1219-XX	SCREW, M5 X 16MM OVAL HEAD, PHILLIPS
	14	212-0591-XX	SCREW, MACHINE; 10-32X.750 OVAL HEAD, POZI
	14	213-0199-XX	SCREW, MACHINE; 12-24 X 0.75, OVH, STL NP, POZ
7	1	351-1095-XX	SLIDE ASSY; PAIR, W/STD HARDWARE KIT AND REAR BRACKET, SAFETY CONTROLLED

The following figure shows an exploded view of the rack kit contents with the identifying item numbers in the preceding table.

Warranted characteristics

When the instrument is installed according to the instructions in this document, the rackmounted instrument meets all warranted requirements listed in the instrument specification. Instruments mounted using methods other than those described in these instructions might not meet their warranted requirements.

For tables of the warranted characteristics, see Specifications in the specification and performance verification manual that applies to your instrument model.

CAUTION:The instrument might be damaged due to overheating. When installing multiple instruments in an instrument rack, the ambient temperature may go up. You assume the responsibility to provide adequate cooling to meet the ambient temperature requirements listed in the specifications.

The ambient temperature inside the instrument rack will vary depending on the location of the instrument within the instrument rack. Tektronix recommends that you measure the ambient temperature in the desired rack location before you install the instrument to ensure the operating temperature does not exceed the rated ambient temperature limit. If necessary, refer to the Environmental Specifications in your product documentation for the operating temperature limits.

Clearance requirements

The rack in which the individual instrument is mounted must provide the following clearance requirements:

At least 218 mm (8.6 in) of vertical space
A minimum width of 488 mm (19.2 in) between the left- and right-front rails in the rack. If possible, consider allowing at least 50.8 mm (2.0 in) on the right side and rear of the instrument for adequate airflow.
A minimum inside depth of at least 384 mm (15.1 in) depth (from rack mounting ear to back of instrument). Airflow enters from the back of the instrument and exits on the right of the instrument when viewed from the front.

CAUTION:Adhering to these requirements mounts the rack-adapted instrument with enough clearance for air circulation and accommodation of the power cord and mounting hardware. Failure to provide these clearances can result in overheating and can cause the instrument to operate improperly or fail.

Installation instructions

These instructions are for qualified service personnel who are familiar with servicing the product. If you need further details for disassembling or reassembling the product, refer to the appropriate product manual. Contact your nearest Tektronix, Inc., Service Center or Tektronix Factory Service for installation assistance.

Assemble the instrument on the rack platform

A 5 Series MSO is shown in the illustrations.

Remove the handle, hubs, and grill as shown. Save the handle, hubs, hub screws, and grill for future use.
Figure 1. Prepare the instrument
Install the left and right mounting plates. Use the M4 screws from item 5.
Figure 2. Mounting plate installation
Install the top and bottom support plates and handle as shown. Use the M3 screws from item 5 to assemble the support plates. Use the 10-32 flat-head screws from item 5 to attach the handles.
Figure 3. Support plate installation
Install the left-side and right-side rack mounts as shown. Use M4 screws from item 5 to attach the slides.
Figure 4. Rack mount installation
Locate the rack slides and using hardware from items 6 and 7, as appropriate for your rack, install the rack slides in your equipment rack.
Figure 5. Installing the rail slides

Install the rack platform in your equipment rack by inserting the platform into the slides as shown.

Figure 6. Installation of rack mounted instrument assembly in rack (top view)

WARNING:To avoid personal injury and prevent the instrument from tipping or dropping, use two or more people to install this instrument into the rack cabinet. After completing the installation procedure, verify that the instrument and the rack cabinet will not tip forward while the instrument is in the extended position. Do not leave the instrument extended when finished accessing the instrument.

Install the power cord. Provide access to a power plug or mains disconnect switch for turning the instrument on/off.
Optionally install any cables you need connected to the instrument rear panel.
Slide the instrument into the equipment rack, and secure the instrument to the rack using standard rack hardware.

My Cart

Your Cart Is Empty

RM5 Rackmount Kit Instructions

相關產品資訊