Electrical Sampling Modules

80E02

Features & Benefits

All Modules

Up to 70 GHz Bandwidth and 5 ps Measured Rise Time (10 - 90%)
Lowest Noise for Analysis – 450 μV_RMS at 60 GHz, 300 μV_RMS at 30 GHz
Remote Samplers*¹ Enable Location of Sampler Near DUT and Ensure Best Signal Fidelity
Independent Sampler Deskew Ensures Easy Fixture and Probe De-embedding
Precision Microwave Connectors (3.5 mm, 2.92 mm, 2.4 mm and 1.85 mm)
Probe Support

TDR Modules

15 ps Reflected True Differential Fully Integrated TDR Rise Time (12 ps Incident) and Feature Resolution Below 1 mm
Efficient, Accurate, Easy to use, and Cost Effective S-parameters up to 50 GHz

Applications

Impedance Characterization and S-parameter Measurements for Serial Data Applications
Advanced Jitter, Noise and BER Analysis
Channel and Eye Diagram Simulation and Measurement-based Spice Modeling

80E02

Device Characterization, Transmission Quality, Waveform Parameters
Low Signal Measurements

Sampling Modules: 80E02

The 80E02 is a dual-channel, 20 GHz sampling modules and provides an acquisition rise time of 28. Optional 2 meter extender cable is available.

When used with Tektronix 80SJNB Jitter, Noise, & BER software, these modules enable separation of both jitter and noise into their components, understand precise causes of eye closure, and obtain highly accurate extrapolation of BER and 3-D eye contour. When used with 82A04 phase reference module, timebase accuracy can be improved down to 200 fsRMS jitter, which together with the 300 μV noise floor and 14 bits of resolution ensures the highest signal fidelity for the measured signals.

Characteristics

	Application Type	Channels	Input Impedance	Channel Input Connector	Bandwidth*¹
80E02	Low-level signals	2	50 ±0.5 Ω	3.5 mm female	12.5 GHz*¹

*¹ Calculated from 0.35 bandwidth rise time product

	Rise Time (10% to 90%)	Dynamic Range	Offset Range	Maximum Operating Voltage	Maximum Non-Destruct Voltage, DC+AC_P-P	Vertical Number of Digitized Bits
80E02	≤28 ps	1.0 V_p-p	±1.6 V	±1.6 V	3.0 V	14 bits full scale

Rise Time

(10% to 90%)

Dynamic Range

Offset Range

Maximum Operating Voltage

Maximum Non-Destruct Voltage, DC+AC_P-P

Vertical Number of Digitized Bits

80E02

≤28 ps

1.0 V_p-p

±1.6 V

3.0 V

14 bits full scale

	Vertical Sensitivity Range	DC Vertical Voltage Accuracy, single point, within ±2 °C of compensated temperature	Typical Step Response Aberrations*²	RMS Noise*²
80E02	10 mV to 1.0 V full scale	± [2 mV + 0.007 (Offset) + 0.02 (Vertical Value - Offset)]	±3% or less over the zone 10 ns to 20 ps;	+10%, –5% or less for the first 300 ps; ±3% or less over the zone 300 ps to 5 ns; ±1% or less over the zone 5 ns to 100 ns; ±0.5% after 100 ns	1.8 mV, ≤2.3 mV (maximum)

Vertical Sensitivity Range

DC Vertical Voltage Accuracy, single point, within ±2 °C of compensated temperature

Typical Step Response Aberrations*²

RMS Noise*²

(before step transition)

(following step transition)

80E02

10 mV to 1.0 V full scale

± [2 mV + 0.007 (Offset) + 0.02 (Vertical Value - Offset)]

±3% or less over the zone 10 ns to 20 ps;

+10%, –5% or less for the first 300 ps;

±3% or less over the zone 300 ps to 5 ns;

±1% or less over the zone 5 ns to 100 ns;

±0.5% after 100 ns

1.8 mV, ≤2.3 mV (maximum)

*² Values shown are warranted unless printed in an italic typeface which represents a non-warranted characteristic value that the instrument will typically perform to

Physical Characteristics

	Dimensions (mm/in.)			Weight (kg/lbs.)
	Width	Height	Depth	Net
80E02	79/3.1	25/1.0	135/5.3	0.4/0.87