Phase Reference Module for the DSA8300*1 Sampling Oscilloscope

82A04

Tektronix 不再銷售此產品規格表上的產品。
檢視 Tektronix Encore 以取得檢修測試設備。
檢查這些產品的支援和保固狀態。

82A04

Features & Benefits

Extremely Low Jitter <200 fs_RMS (typical)
Flexible Operation

Triggered
Untriggered (Free-running) Acquisition Without Trigger Signal

Support for Enhanced Acquisition Modes (FrameScan^®)
Wide and Continuous Frequency Range 2 GHz - 60 GHz
Small Module Implementation Allows:

Acquisition on Six Other Channels
Placement Close to the DUT with Module Extender Cable

Fast Acquisition Rate

Applications

Design, Verification, and Manufacturing of Telecom and Datacom Components and Systems Operating at 10 Gb/s and Faster

Extremely Low Jitter, Flexible Signal Acquisition Solution

The 82A04 Phase Reference Module extends the capability of the DSA8300*¹ digital serial analyzer sampling oscilloscope mainframe by providing extremely low jitter/drift sample position information to the mainframe. This sample position information is based on the phase of a clock the user provides to the 82A04 input.

The benefits of using the sample position information based on a clock signal are two-fold – an extremely low jitter of <200 fs_RMS (typical), and the possibility of a triggerless acquisition. The typical application is the acquisition and analysis of very high-speed optical and electrical signals in high-speed communication devices and systems and similar areas.

The 82A04 together with the DSA8300 implements the phase reference time-base functionality in a novel way, giving the user the freedom to select from time base and acquisition modes without compromises; any phase-reference frequency within the operating range is accommodated, and even the advanced features, such as FrameScan^®, remain available. The separate DSP per acquisition slot architecture of the DSA8300 enables the acquisition rate in the Phase Reference mode to reach over 40 kS/s*².

*¹ Also compatible with DSA8200, TDS/CSA8200 sampling oscilloscopes.

*² Typical performance, some settings will lower the throughput.

Modes of Operation

The operation of the phase reference is based on the acquisition of a clock synchronous to the signal under observation. This clock can be a user-supplied signal (e.g. a clock from a BERT), or the clock output of one of the DSA8300 clock recovery or optical modules. In addition, the user can also provide a traditional external trigger signal either to the Direct Trigger input, or to the Trigger Prescaler input of the mainframe.

Phase Ref Free-Run - With no external trigger to the DSA8300 mainframe needed, the 82A04 module can, together with the mainframe, create a time base based on the phase of the reference clock (effectively the time base of the instrument functions as a “Phase-base” instead). The signal displayed on the screen will therefore repeat after one period of the reference clock. All user controls remain enabled, even while the horizontal position has relative meaning only. The timing information presented by the oscilloscope is based solely on the phase reference clock frequency as entered by the user in the Input Freq field of the Phase Reference Setup dialog.

Phase Ref Triggered - When the DSA8300 mainframe is supplied with both the reference clock and a traditional external trigger, the mainframe triggers on the trigger signal, and uses the phase reference information from the 82A04 to minimize the jitter. Otherwise the acquisition process doesn’t change from traditional acquisition, the signal remains referenced to the trigger point.

Characterize - To operate properly in either the Phase Ref Triggered or the Phase Ref Free-Run modes the Phase Reference module has to first characterize the phase reference signal. The signal needs to be stable during the characterization and afterward. The instrument indicates when characterization is necessary.

Performance You Can Count On

Depend on Tektronix to provide you with performance you can count on. In addition to industry-leading service and support, this product comes backed by a one-year warranty as standard.

Characteristics

Characteristic	Description
Acquisition Modes	Free Run Synchronous, Triggered Synchronous
Mainframe Resources	Any one active*³ small (electrical) module slot. Both acquisition channels associated with the slot became unavailable. Only one 82A04 module can be activated in a mainframe at a time
Compatible Mainframes	DSA8300, DSA8200, CSA/TDS8200. Does not operate in the CSA/TDS8000 or 8000B mainframes

*³ Channels not displaced by a large (optical) module.

Reference Clock Parameters Supported

Characteristic	Description
Amplitude
Operational	100 mV_p-p - 1.8 V_p-p Jitter performance guaranteed from 600 mV_p-p - 1.8 V_p-p
Guaranteed Frequency Range	2 GHz - 25 GHz continuous; for non-sinewave reference clock signal in the 2 GHz - 8 GHz range an additional filter⁴ typically is required 2 GHz - 60 GHz continuous with Option 60G; for non-sinewave reference clock signal in the 2 GHz - 8 GHz range an additional filter⁴ typically is required

Characteristic

Description

Amplitude

Operational

100 mV_p-p - 1.8 V_p-p

Jitter performance guaranteed from 600 mV_p-p - 1.8 V_p-p

Guaranteed Frequency Range

2 GHz - 25 GHz continuous; for non-sinewave reference clock signal in the 2 GHz - 8 GHz range an additional filter*⁴ typically is required

2 GHz - 60 GHz continuous with Option 60G; for non-sinewave reference clock signal in the 2 GHz - 8 GHz range an additional filter*⁴ typically is required

*⁴ See list of accessories at the end of this datasheet for recommended filters.

System Performance

Characteristic	Description
Jitter	System jitter of 200 fs_RMS typical, on a 10 GHz or faster acquisition module, in DSA8300 mainframe, with f ≥8 GHz, VREF ≥0.6 V Phase Reference Signal System jitter of 280 fs_RMS typical, on a 10 GHz or faster acquisition module, in DSA8300 mainframe, with 2 GHz ≤ f <8 GHz, VREF ≥0.6 V Phase Reference Signal

Characteristic

Description

Jitter

System jitter of 200 fs_RMS typical, on a 10 GHz or faster acquisition module, in DSA8300 mainframe, with f ≥8 GHz, VREF ≥0.6 V Phase Reference Signal

System jitter of 280 fs_RMS typical, on a 10 GHz or faster acquisition module, in DSA8300 mainframe, with 2 GHz ≤ f <8 GHz, VREF ≥0.6 V Phase Reference Signal

Time Accuracy (Time Base) and Timing Deviation (Phase Reference)

Characteristic	Description
Phase Reference Time Base (Triggered)
Maximum timing deviation relative to phase reference signal	Horizontal position >40 ns after trigger event: 0.2% of phase reference signal period (typical) Horizontal position ≤40 ns after trigger event: 0.4% of phase reference signal period (typical)
Phase Reference Time Base (Free Run)
Maximum timing deviation relative to phase reference signal	0.1% or better of phase reference signal period (typical)

Input

Characteristic	Description
Input Impedance	50 Ω ±0.5 Ω AC (5 pF typical AC coupling) 1.85 mm female (‘V’) connector Precision adapter to 2.92 mm female included with 50 Ω SMA termination

Characteristic

Description

Input Impedance

50 Ω ±0.5 Ω AC (5 pF typical AC coupling)

1.85 mm female (‘V’) connector

Precision adapter to 2.92 mm female included with 50 Ω SMA termination

Environmental

Matches the mainframe specifications.

Physical Characteristics

Dimensions	mm	in.
Width	79	3.1
Height	25	1.0
Depth	135	5.3
Weight	kg	oz.
Net	0.4	13

Ordering Information

82A04

Phase Reference Module.

Includes: User manual (1); Precision adapter 1.85/2.4 mm male to 2.92 mm female included with 50 Ω SMA termination (1), one-year warranty.

82A04 Options

Option	Description
Opt. 60G	Extends the BW range to 60 GHz
Filter	For non-sinusoidal phase reference clock signal with frequency below 8 GHz please also order appropriate filter from the accessory list below

Service Options

Option	Description
Opt. C5	Calibration Service 5 Years
Opt. R3	Repair Service 3 Years
Opt. R5	Repair Service 5 Years

Other Accessories

Accessory	Description
020-2566-xx	82A04 Filter 2 GHz. Filter kit for non-sinusoidal phase reference clock signal with frequency between 2 GHz and 4 GHz
020-2567-xx	82A04 Filter 4 GHz. Filter kit for non-sinusoidal phase reference clock signal with frequency between 4 GHz and 6 GHz
020-2568-xx	82A04 Filter 6 GHz. Filter kit for non-sinusoidal phase reference clock signal with frequency between 6 GHz and 8 GHz
80N01	Sampling Module Extender Cable (2 meter)*⁵
011-0157-xx	Connector Adapter. (2.4 mm or 1.85 mm male to 2.92 mm female) DC to 40 GHz

Interconnect Cables (3^rd party)*⁵

Tektronix recommends using quality high-performance interconnect cables with these high-bandwidth products in order to minimize measurement degradation and variations. The W.L. Gore & Associates' cable assemblies, accessible at http://www.gore.com/tektronix, are compatible with the 2.92 mm, 2.4 mm, and 1.85 mm connector interface of the 80E0x modules. Assemblies can be ordered by contacting Gore, at the URL above.

*⁵ The 82A04 module does not require particularly high spectral fidelity in the clock signal passed to it; the signal can be BW limited (e.g. by the cable) since there can be no ISI issues (as the signal is a clock); it is sufficient to supply a signal that is stable, free from unstable moding, and has the appropriate amplitude. Similarly the module extender cables are of lesser benefit to the 82A04 than to the usual acquisition modules.