Тестирование Ethernet

Tektronix предлагает обширный набор интегрированных средств для проверки физического уровня устройств IEEE 802.3 Ethernet, а также разработки и отладки систем на базе Ethernet от 10BASE-T до 40/100GB.

Tektronix предлагает также передовые приборы для проверки на соответствие стандартам и отладки по другим стандартам передачи данных, например 10BASE-T, 10BASE-Te, 100BASE-Tx, 1000BASE-T, BroadR-Reach, 10GBASE-T, 10GBASE-KR, SFP+ (SFF 8431), QSFP+ (SFF-8634), Fiber Channel FC-16G (FC-PI-5) и CEI-28G-VSR.

Избранные материалы

Краткое справочное руководство «Понятие и определение характеристики джиттера»

Джиттер тактовой частоты — это нежелательный спутник всех электрических систем, которые используют разность потенциалов для представления информации о тактовой частоте. Этот документ посвящен, главным образом, джиттеру в электрических системах.

Загрузить

Руководство по применению «Структура глазковой диаграммы»

Это руководство по применению содержит сведения о различных способах получения информации из глазковой диаграммы для лучшего понимания. Также в нем обсуждаются некоторые основные способы тестирования передатчиков, каналов и приемников.

Загрузить

Видеоролик «Приложение TDSET3 для автоматизированного анализа соответствия стандарту Ethernet»

Тестирование для проверки на соответствие стандарту Ethernet можно упростить при помощи автоматизированной системы тестирования Tektronix TDSET3. TDSET3 обеспечивает проведение проверки на соответствие стандартам 10BASE-T, 100BASE-TX и Giga-bit Ethernet.

Посмотреть сейчас

Title
Understanding and Characterizing Timing Jitter Primer Timing jitter is the unwelcome companion of all electrical systems that use voltage transitions to represent timing information. This paper focuses primarily on jitter in electrical systems..
Characterizing an SFP+ Transceiver at the 16G Fibre Channel Rate Study the measurements needed to test an SFP+ transceiver to the 16G Fibre Channel standard, covering both Multi- Mode 850 nm and Single Mode 1310 nm interfaces. Included is a test and …
The Basics of Serial Data Compliance and Validation Measurements Serial Buses - An Established Design Standard High-speed serial bus architectures are the new norm in today's high-performance designs. While parallel bus standards are undergoing some …
DesignCon 2015 Paper – Hybrid Modeled Measured Characterization of a 320 Gbit/s Backplane System This paper explores a case study of a multilane Ethernet backplane 320 Gbit/s system that is difficult to fully measure and deembed, implements a hybrid method of modeling, deembedding, and …
Comparison of New versus Legacy Ethernet Compliance Test Automation New test automation software is available for Ethernet 1000BASE-T, 100BASE-TX, and 10BASE-T compliance testing. The new "CMENET3" solution is based on the TekExpress framework and provides …
The Benchmark for Fast+ Accurate Ethernet Compliance Measurements Tektronix Ethernet compliance measurement tools provide an efficient physical layer solution for 10BaseT, 100BaseT, and 1000BaseT Ethernet implementations. High-performance hardware and integrated …
100BASE-TX Method of Implementation (MOI) Tektronix Test Methods of ImplementationThis Tektronix guide to measurements document is provided "AS IS" and without any warranty of any kind, including, without limitation, any express or implied …
10BASE-T Method Of Implementation (MOI) Tektronix Test Methods of ImplementationThis Tektronix guide to measurements document is provided "AS IS" and without any warranty of any kind, including, without limitation, any express or implied …
SFP+ QSFP+ DPOJET MOI SFF-8431 – SFP+ QSFP+ Measurements & Setup Library Methods Of Implementation (MOI) for Verification, Debug, Characterization, Conformance Test
1000BASE-T Method of Implementation Tektronix Test Methods of ImplementationThis Tektronix guide to measurements document is provided "AS IS" and without any warranty of any kind, including, without limitation, any express or implied …
Teranetics Turns to Tektronix to Validate First Dual-Port 10GBASE-T PHY Case Study ChallengeBring first dual-port 10GBASE-T PHY to market and make testing of complete IEEE 802.3an specification faster and more affordable for partners.SolutionTektronix XGbT software, Tektronix …
Jitter Testing for 1000BASE-T Ethernet Compliance Application Note Compliance testing for IEEE 802.3 Ethernet standards such as 10BASE-T, 1000BASE-Tx and 1000BASE-T requires jittter testing to ensure interoperability. This application note describes test fixtures …
Troubleshooting Ethernet Problems with your Oscilloscope This Application Note: • Gives a brief orientation on the physical layer and packet structure of Ethernet, with a goal of providing just enough detail to help with …
Physical Layer Compliance Testing for 10GBASE-T 10GBASE-T Ethernet introduces new challenges for design and test. Find out about tools that deliver proper and optimal electronic testing for the validation of your 10GBASE-T designs in this …
Debugging Serial Buses in Embedded System Designs Find out how the protocol trigger, decode and search capabilities of the popular MSO and DPO Series oscilloscopes solve serial bus integration and debug challenges of many buses such as I2C, SPI , USB …
Time Domain Methods for Measuring Crosstalk for PCB Quality Verification Application Note This application note discusses the elements of crosstalk and demonstrates how you can measure crosstalk on a single-layer PCB using the TDS8200 Series Sampling Oscilloscope or the CSA8200 Series …
Variations in 10 Gigabit Ethernet Laser Transmitter Testing Using Reference Receivers One of the key tools used by telecom/datacom original equipment manufacturers, system installers and system servicers to view eye patterns on an oscilloscope and test the quality of a laser’s time …
$name
Physical Layer Compliance Testing for 100BASE-TX This application note describes various physical layer tests including amplitude domain, return loss, jitter and duty cycle-distortion and compliance testing using TDSET3 software.