WVR7120 WVR7020 AND WVR6020 SYSTEM FIRMWARE CUSTOMER DISTRIBUTION v5.2.4 V5.2.4

Software version 5.2.4: This release is for customers of the WVR6020, WVR7020, WVR7120. This firmware also supports WVR6100, WVR7000 and WVR7100

Version: V5.2.4
Software Type: Firmware

Release Date: Nov 06 2009 - 08:00 am
Part Number: 063382708

Pre-Requisites/System Requirements

Release Notes

Instructions

Prerequisites

Windows PC, ethernet connection and crossover cable

Release Notes

Release Notes
WVR6020, WVR7020, WVR7120, WVR6100 Opt. MB, WVR7000 Opt. MB, and WVR7100 Opt. MB Waveform Rasterizers

Copyright © Tektronix.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Release Notes

These release notes support software version 5.2.X and greater. The release notes
apply to instruments with the indicated measurements or options installed. See
the Quick Start User manual or visit www.Tektronix.com for a list of options
available for each model.

Known Issues and Behaviors
The following pages describe known issues and behaviors of the waveform
rasterizers. Topics are listed in alphabetical order.

Advanced Diagnostics
*The following items may appear when you run the Advanced Diagnostics on your
instrument. If one or more of these appear, re-run the Advanced Diagnostics. The
instrument does not require any service if these messages are reported sporadically.

*Eye Cable A2D Fail: message may incorrectly appear on the screen
*Fail Adv Diag Test Suite: this may be recorded in the Diagnostic Log
*Fail Eye Option: this may be recorded in the Diagnostic Log

ANC Data Reporting
*The ANC data displays report the incorrect line number for dual link 50p, 59.94p,
and 60p formats.

Audio
*Audio DSP heartbeat errors may be reported sporadically in the diagnostics
log. The audio monitoring features are not impacted by this behavior. The
instrument does not require any repair if this error is reported sporadically.

*When the Audio display is active and the audio input is changed, the displayed
audio scale may not update automatically. Press the FULL button to toggle
the display and update the audio scale.

*When the instrument is in dual link mode and there are two or more trace
displays in other tiles, the Audio Phase display for 50p, 59.94p, and 60p
formats is not displayed.

NOTE. See SIM Mode for audio issues related to SIM mode operation.

Black and Frozen Frame
*Black and Frozen readouts in the Video Session Display are functional for SD and
HD. The readouts are present but not functional for dual link.

Calibration and Performance Verification
*Before entering Calibration, connect any supported SDI signal to the SDI A
input, select Input A, verify lock, then disconnect the SDI signal and start
Calibration.

*On some units, the calibration screen might not be displayed after selecting
CONFIG > Utilities > Calibration. If this occurs, press the STATUS button to
display the calibration screen.

*Do not select SDI Deserializer Mode in the calibration menu during Eye Gain
and Eye Signal Bandwidth performance verification. Instead, select Eye Gain
Adjust SDI A to check the SDI A input, and select Eye Gain Adjust SDI
B to check the SDI B input.

CAUTION. Select "Exit" (instead of "Save" or "Save then Exit") to leave the
calibration mode without saving the settings. To avoid lost settings, record
the values of the Eye Gain Adjust SDI A and B settings before initiating those
calibration steps by pressing SEL. If either setting is accidently changed during
performance verification, return the settings to their original values when the
calibration step is complete

*If a clean waveform is not seen when Eye Gain Adjust is selected, then
remove the calibration signal and connect an SD SDI signal to the selected
SDI input. After the SDI eye diagram is stable, remove the SDI signal and
reconnect the calibration signal.

*After calibration is complete, instrument power must be cycled to restore
normal operation.

Capture and Freeze
*Capture Buffer is designed to capture digital video only, and not analog video.

*You can select Capture Buffer while monitoring a composite video input,
but there will be no effect because the Capture Buffer mode does not apply
to composite analog signals. Use the Capture Freeze mode when monitoring
composite analog signals.

*Short duration trigger events are captured, but "frozen" status displays such as
video session may not update in time to reflect the event.

*Captured format must match input. When viewing capture buffer data, ensure
a signal with the same format is on the selected input.

*Capture mode works when at least one tile is one of the following: waveform,
vector, gamut, or picture.

*Use Freeze instead of Buffer to capture physical layer characteristics.

*Selecting to delete the capture buffer from the Remote UI does not delete
the capture buffer.

*Manipulating Capture data (such as changing display types or changing to
full screen) can introduce spurious errors in the captured status and session
screens.

*Capture buffer playback is disabled in tiles 3 and 4 and forced into frozen
mode when the instrument is set to Black or Frozen Frame mode.

Display Distortion
*The audio phase display is optimized for a 4 x 3 monitor. When an external 16 x 9
XGA monitor is used, the X-Y axes of the audio phase display are not 90 degrees
apart and the waveform is stretched somewhat horizontally.

Dolby Bar Labels
*Depending on the current state of the input, surround channels may be indicated
by numbers 1-10, rather than by labels L, R, C, and so on. The channels, if
present in the AUDIO display, allow the Channel Labels to be present in both
the audio input/output maps in the CONFIG menu and in the audio session. If
channels are not present (input shifts from 5.1 to Stereo or downmixes are turned
off), the affected bar numbers appear in the session and maps, replacing the
Channel Labels. In the alarm status and error log, bar numbers are always shown
regardless of the input format.

Dolby Operation With Option DDE
*In the AUDIO display, with a Dolby Digital input and a nonexistent stream
selected, the downmix level bars continue to display levels instead of going to
Mute status. The other bars go to Mute status as expected.

*For listening mode selections other than FULL or EX, clipping may
occur. For example, if the Dolby Digital input is 3/2 with full-scale test
tones and Stereo listening mode is selected, clipping will likely occur.
To avoid clipping, choose either compression mode, Dialnorm+Line or
Dialnorm+RF, in CONFIG > Audio Input/Outputs > Dolby D (AC-3) Setup >
Dialnorm&DynRng.

*When in Channel Mode 2/2 and Phantom Listening Mode, the Surround
Sound display (AUDIO tile) shows the Ls and Rs levels attenuated by 3 dB
instead of displaying at full amplitude for this channel mode/listening mode
combination.

*When in Channel Mode 3/0 and 3-Stereo Listening Mode, the Surround
Sound display (AUDIO tile) shows the C level attenuated by 3 dB instead
of displaying at full amplitude for this channel mode/listening mode
combination.

*The Dolby E/Dolby Digital decoder will pass through PCM audio at 48 kHz
frequencies or less. Audio frequencies above this will not pass through and
may cause noise or distortion on both the bars and the audio outputs. If PCM
audio at frequencies greater than 48 kHz is used, choose either AES A or
B as the input source.

*For Dolby Digital (AC3) signals, the header in the Audio display may show
Channel Mode incorrectly. See the Dolby Status display for the correct
indication of Channel Mode.

Embedded Audio Active Bits (SD Only)
*The Audio Active Bits field only reports up to 20 bits for SD.

Error Readouts
*If every CRC or Line Number in a signal is incorrect, the status screen will
display "Error" for a couple of seconds and then go back to "OK", even if the
error is still present. If the error is present when the signal if first connected, it
is never detected.

External Reference
*Sometimes loss of the External Reference signal does not make the resulting
loss of lock obvious. For example, if a 525 input has EXT REF selected and
configured to lock to an NTSC reference, removing the external reference
signal leaves the waveform stable, but shifted on the screen.

*Note that the SDI Input Readout can be used to determine if the waveform is
locked

*When in SDI mode, but with no SDI input signal present, the screen
displays Ref: Ext Unlocked even though a valid External Reference signal
is connected.

*The following External Reference signal formats are not fully supported when
in line select mode or in Sweep MAG mode. Although not supported, the
following formats may be somewhat functional and are not locked out: NTSC
and PAL with tri-level input, and 720p 23.98, 1080sf 29.97, 720p 24, 1080sf
30, 720p 25, and 1080sf 25.

*With some combinations of SDI input and External Reference formats, the
sweep stops prematurely when Sweep MAG is in one-line mode. To work
around this limitation, turn off EXT REF to make the measurement.

Field Installs of Dolby Options
*When you update an instrument with Option DDE, the Dolby input entries may
not appear in the Audio popup menu until you cycle power. Therefore, after
installing an option and powering up and updating the Option Key, be sure to
cycle power once more to ensure that the menu items appear.

NOTE. See Dolby Operation With Option DDE for Dolby and Option DDE
related information

Incompatible Operation
*When applying SD or HD signals to any rasterizer that does not support them, the
unit indicates that the signal input is not standard. Applying unsupported video
signals may result in a frozen PICT display.

OP47 Teletext
*The OP47 Protocol Error alarm may not trigger accurately. To avoid getting this
error, disable the alarm in CONFIG > Alarms > Closed Captions/Teletext.

SDI Status Display
*When the input signal is missing, the Cable Length meter, the Cable Length
readout, and the Cable Loss readout on the SDI Status display indicate zero. Use
the Input Status on the Status Bar for the actual signal state.

Simultaneous Input Mode (SIM)
*To access Analog Output Mapping and AES Output Mapping settings while
in simultaneous input mode, go to CONFIG > Audio Inputs/Outputs > Dual
Audio > Audio Inputs.

*The phase pair selected as an audio source is for the channel of the phase
pair you changed last.

*External Reference reports unlocked if no SDI A signal is on Channel 1.

*Selecting AES B as a source when it is an output causes a blank tile.

SNMP Messages
*Commands returning the audCurOutput OID return the string "Embed 7 & 8"
for embedded audio channel pairs 9 & 10, 11 & 12, 13 & 14, and 15 & 16.

*The MIB contains the command dolbyPgmAvg, but the command name does
not indicate that the OID is for loudness.

*The MIB contains the dolbyPgmCurLoudness command. However, it does
not contain a command for program session loudness.

Sweep
*The waveform style must be set to Overlay to get 2 line or 2 field sweep.

Sweep MAG
*When in 2 line mode, waveform displays of SD or composite inputs will display
invalid information at the left and/or right side of screen (beginning and/or end of
sweep) when Sweep MAG is on. HD formats are unaffected.

Waveform Mode Cursor for XYZ Color Space
*The voltage cursors are given in millivolt scale, but the XYZ color space is
referenced in hex scale. If you want to see the values for 000 to FFF, change the
graticule settings to max and percent.

Web Browser
*The Web browser applet will not resize when running in some versions of
the Netscape browser and in some non-Windows Operating Systems (for
example, Solaris).

*We recommend using Java Runtime Engine (JRE) version 1.6.

Instructions

By downloading, you agree to the terms and conditions of the Software Download Agreement.

This software applies to: WVR7000, WVR7100, WVR6100, WVR7120, WVR7020, WVR6120

WVR7120 WVR7020 AND WVR6020 SYSTEM FIRMWARE CUSTOMER DISTRIBUTION v5.2.4 V5.2.4

Prerequisites

Release Notes

Instructions

Related Product Information