TG700 Software Download V5.62

This release repairs defects found in earlier versions of the TG700 firmware.

Version: V5.62
Software Type: Firmware

Release Date: Mar 06 2013 - 08:00 am
Part Number: 066083414

Pre-Requisites/System Requirements

Release Notes

Instructions

Prerequisites

This version of firmware requires a TG700 mainframe with at least 32 MB of memory. A 16 MB or 32 MB system may be upgraded to 64 MB by ordering the upgrade kit PN: 040-1698-10.

Release Notes

TG700 TV SIGNAL GENERATOR PLATFORM
Release Notes
077-0228-09

Firmware Update 5.62
February 22, 2013

This document describes new features, improvements, and limitations
of firmware version 5.62 for the TG700 Signal Generator Platform.

This release repairs defects found in earlier versions of the
TG700 firmware.

New Features
------------

This release introduces the following new features:

SDI Module Logo Overlay with Moving Picture Enabled

On test signals generated by the SDI7 module, the logo overlay
will remain in the user-set location even when the Moving Picture
feature is active.  However, the logo overlay will move with the
picture when a Frame Picture signal is selected.

SDI7 Module Audio Mute and Disable Controls for the Secondary
Output

Two new selections have been added to the configurations for the
secondary output on the SDI7 module:  Black (with no audio) and
Black (with audio muted).  If embedded audio is enabled for the
SDI7 module, the audio on the secondary output (lower BNC) will be
controlled by this setting.

DOCUMENTATION CHANGES
---------------------

The following documentation changes cover the new features that are
being introduced with this release.

SDI7 Module Moving Picture Submenu

NOTE:  The following information replaces the contents of the NOTE
in the MOVING PICTURE Submenu section for the SDI7 module in the
TG700 User Manual (Tektronix part number 071-1970-07).

The Moving Picture function is not available with zone plate or
multiburst signals.  However, zone plate signals may be defined with
motion in the zone plate parameters.  (See page 3-260, Modifying
a Zone Plate Signal.)

The Moving Picture function is enabled whenever the H Step or V Step
parameter is set to a value other than 0.

When Moving Picture is enabled, the circle and text overlays remain
static regardless of the signal type (standard test signal or "frame
(.BMP) picture").  However, the logo overlay remains static for only standard test signals.

SDI7 Module SECONDARY OUTPUT Submenu

NOTE:  The following information replaces the description of the
SECONDARY OUTPUT Submenu for the SDI7 module in the TG700 User Manual
(Tektronix part number 071-1970-07).

Use the left or right arrow button to select the test signal to be the
output for the secondary (Signal 1B or Signal 2B) BNC connector for
the selected SDI7 channel.  Press the ENTER button to confirm the
selection.

The SECONDARY OUTPUT submenu has the following selections:

Test Pattern
When set to Test Pattern for channel 1, the Signal 1A and Signal 1B
connectors will output the same test signal.  The same is true for
the channel 2 connectors when Test Pattern is set as the Secondary
Output selection for channel 2.

Black
When set to Black for channel 1, the signal 1B black signal is the
same format and sample structure as the Signal 1A output.  The same
is true for the channel 2 connectors when Black is set as the
Secondary Output selection for channel 2.

Black (No Audio)
Operates like the Black selection above, except that the output
signal contains no audio content.

Black (Mute Audio)
Operates like the Black selection above, except that the output
signal contains muted audio, if embedded audio is enabled for the
selected output channel.

SDI7 Module OUTPUT<x>:BLACK Remote Command

NOTE:  The following information replaces the description of the
OUTPUT<x>BLACK remote command for the SDI7 module in the TG700
Programmer Manual (Tektronix part number 077-0139-06).

:OUTPut<1|2>:BLACk TEST | BLACK | BLK_NOAUD | BLK_MUTE

Sets the signal for the active video of the second output (i.e.,
SIGNAL 1B or SIGNAL 2B) of the specified generator channel.  When
TEST is selected, the second output is a copy of the test pattern
on the first output (i.e., same as SIGNAL 1A or SIGNAL 2A,
respectively).

When any one of the three Black signals is selected, the second
output is digital black (0% flat field).  Select BLACK to include
audio content at the default volume.  Select BLK_NOAUD to remove
audio content from the Black signal.  Select BLK_MUTE to include
audio content that is muted in the Black signal, if embedded
audio is enabled for the selected output channel.

For any of the four settings, the ancillary data (time code,VPID,
and user-defined data) will be the same for both outputs of the
specified generator channel.

GENERAL LIMITATIONS
-------------------

This release has the following general limitations:

TG700 Mainframe Memory Requirements:

With software version 5.61, the TG700 mainframe must have at least
32 MB of memory installed.  If you intent to install frame picture
files (*.pic), created by the Frame Picture Generator application
for the DVG7, HDVG7, AVG7 or AWVG7 modules, or if you intend to
install bitmap frame picture files (*.bmp) for the SDI7 module,
then the mainframe must have 64 MB of memory installed.

Software Upgrades:

If your existing mainframe has 32 MB of memory and you have loaded
the TG700 memory with signals from the Frame Picture Generator
application, you may not be able to upgrade the instrument to
software version 5.61.

If you receive a memory error while attempting to upgrade the
software version, you need to either delete some of the frame
picture files or upgrade your instrument to 64 MB of memory.

Memory Upgrades:

------------------------------------------------------------------
NOTE: Option FP provided extra memory, which allowed the TG700
mainframe to support frame picture images.  This option is no
longer necessary for new TG700 mainframes.

If you have an older mainframe with less than 64 MB of memory,
you can increase the memory in your mainframe to 64 MB by ordering
the following upgrade kit:  040-1698-xx.  Contact your local
Tektronix representative for more information.
------------------------------------------------------------------

TG7 Setup Software:

- In setting signal formats for the Black 2 and Black 3 outputs of the
AGL7 module, do not select Black 2 = HD sync (same as Black 3) and
Black 3 = BB (same as Black 2) simultaneously, while Frame Reset 1
is set to 2.997 Hz. This operation makes the Frame Reset 1 unstable.
If this is the case, reset the system by recalling the Power On
Default setting or a preset.

TG7 Comm Software:

- Do not change or delete any file names or folder names other than
those downloaded by users (signal files, sequence files, and preset
files). Doing so can cause the instrument to operate in an
unexpected manner.

You can change the names of user files (signal files, sequence
files, and preset files) after you have downloaded them into the
TG700 mainframe.  Remove and reapply power to see the updated names
on the mainframe.

Resetting an Output Signal:

- When the instrument rereads or resets signal data, such as format
changing, preset recall, or signal-button assignment, a signal
output interruption or synchronization shock may occur.

Setting the Genlock Source:

- If you change the frame reset period in the AGL7 module after the
genlock source is set to CW, the frame reset may not be selected
properly. If this is the case, set the frame reset to CW.

Assigning a Signal and Frame Picture to a Front-Panel Button:

- When you assign a downloaded signal to a front-panel button, do not
assign different format signals to the same button.

- Do not assign a signal set to a signal button of the signal that is
currently being output. Also, do not assign a signal set to a signal
button while the message "No Signal Set Assigned" is displayed. If
you reassign a signal set to the OTHER button, perform the
reassignment while a signal that is assigned to a button other than
the OTHER button is output.

Embedded Audio of the HDVG7 Module:

- Embedded audio for 720 23.98p/24p formats is not supported for the
HDVG7 module, even though it can be selected in the menus.

- The first user data word in the audio control packet (containing the
Audio Frame value) has incorrect parity when the frame count is 1,
2, or 4.

Y-to-GBR Converter Mode of the HDLG7 Module :

- If the output format is 2K and the Converter mode is set to Y to
GBR, changing operating mode by selecting a test signal will cause
an unexpected black and white signal to be generated. To correct the
test signal, press the OTHER button until Normal is selected, and
then press the test signal button.

25/29.97/30 Hz Segmented Frame Formats for the HDLG7 Module:

- The HDLG7 module does not have format selections for 1080PsF at
25 Hz, 29.97 Hz, or 30 Hz. These formats are almost identical to
1080i (interlaced) formats at 50 Hz, 59.94 Hz, and 60 Hz
respectively; these format settings can be used with progressive
segmented signals. However, note that the SMPTE 352M payload
identifier for the output signal will show an interlaced signal
format, even when the HDLG7 module is converting a single link
progressive segmented input signal to dual link.

Multiple Timecode Formats:

- Frequent changes to output formats can result in instability on
those outputs. Disturbances to PAL output signals can be prevented
by setting any output to PAL as a power-on preset, and then keeping
any output set to PAL at all times.

Converter Mode of the HD3G7 Module:

- Infrequently, the module will fail to up-convert the input HD-SDI
signal.  If no output is seen, the problem can be corrected by
selecting a different test signal then switching back to converter
mode.

- The trigger output cannot generate a frame pulse or a line pulse
when the module is in converter mode.

- The moving picture and video component functions do not apply to up-
converted output signals.

Embedded Audio of the HD3G7 Module:

- When a Level B format is selected for the up-converted 3 Gb/s output
signal, embedded audio from the input HD-SDI signal  will be copied
onto both  virtual links.  Therefore, up to 32 channels of embedded
audio can appear on the 3 Gb/s output.

Time of Day Changes For Timecode Outputs:

- When the time-of-day changes, such as when scheduled daylight
savings adjustments are made or when the internal time is set from
the front panel, there can be a delay before that change is
reflected on timecode outputs.

This delay may be a small number of frames (fraction of a second)
when all timecode output formats are based on the same clock rate
(for example, NTSC black burst and 1080i 59.94 HD trilevel on black
outputs in addition to 30 fps drop-frame on LTC outputs), or up to
several seconds when timecode formats based on different clock rates
are used (for example, 29.97 fps and 24 fps on different outputs).

Closed Caption Data with the HD3G7 Module in Converter Mode:

- The HD3G7 module does not re-format SMPTE 334 Caption Distribution
Packets in converter mode. Therefore, when up-converting from 1080i
59.94 Hz to 1080p 59.94 Hz, for example, the output will contain CDP
data in alternate frames, each with 40 bytes of caption data,
instead of CDP data in every frame, each with 20 bytes of caption
data.

- Up-conversion to a Level B fast progressive format may result in
mis-ordered Caption Distribution Packets in the stream of output
frames.

SDI Equalizer Test Signal of the HD3G7 Module:

- Per SMPTE RP198 for HD-SDI, a polarity change word is used to ensure
equal probabilities of the DC bias for the equalizer test pattern.
However, some 3G SDI formats still exhibit an unequal bias. Enabling
a dynamic bit stream in the output signal, such as embedded audio or
timecode data, will result in both dc levels appearing in the output
signal.

Changing Output Formats with Open Menus:

- Some front-panel menus and status displays are dependent on the
frame rate of the currently selected output format. If you open a
submenu and press the FORMAT button to change the frame rate, the
submenu will not be refreshed until it is exited and reopened.

Test Signal Files of the HD3G7 Module:

- The HD3G7 module now uses file-based test signal definitions.  If
you modify a signal from the factory version, unpredictable results
may occur.  To recover from this situation, reload the factory
version of the signal file from the "TG700 Software Library and
Documentation DVD" that was supplied with the instrument.

HD3G7 Module Presets

- If a preset was made with an earlier version of the HD3G7 module and
recalled with version 5.61, the test signal selection is not
restored.  All other settings are restored normally.

Timing Range of AGL7 Module

- The TIMING menu for the AGL7 module will allow output timing
adjustment beyond +/- 1/2 frame of the current format.

Daylight Savings Time (DST) Scheduler System:

- The DST scheduler system applies the DST offset even if the
Time-Of-Day (TOD) source is set to "VITC Input" or "LTC Input".
In both cases, the offset is applied whether or not a valid VITC
or LTC input signal is available.  For proper DST scheduling, you
need to manually enter the date and time in the TOD menu and
assure that the instrument has valid time information.

When the TOD source is set to "GPS signal" and the GPS is not
locked to the input signal, the DST scheduler system will apply
the DST offset when the internal time of day clock (which starts
at a fixed default and may not be correct) reaches the time
scheduled for the DST offset to be applied or removed.  Ensure
that the GPS is locked and that the system time of day is correct
before turning on the DST scheduler system.

If the TOD source is set to "Internal" when the instrument is
powered on, you will need to change the TOD source to "VITC Input",
"LTC Input", or "GPS Signal" and then back to "Internal" in order
to enable the DST scheduler system with "Internal" as the TOD
source.  Check the system time of day and adjust as needed to
ensure that it is correct before enabling the DST schedule in
"Internal" mode.

DHCP Service on Instrument Power-up:

- When the instrument is configured for DHCP service and then is
powered down, the service may not always restart automatically
when the instrument is powered up.  If this is the case, use the NET
SETUP subment to first disable DHCP, and then to immediately
re-enable DHCP.

SDI7 Multi-language Support:

- Languages that require combined glyphs in order to be represented
may not be correctly rendered in the Text ID display on the
SDI7 module.

SDI7 Response Time:

- The response time for loading a frame picture or logo display, or
for loading text and/or circle overlays will vary depending on
the size of the picture/data file and the number of characters in
the text overlay.

Multiburst Signal Motion:

- Do not set a Multiburst signal in motion on the SDI7 module.
Otherwise, a corrupted signal will be generated.

Instructions

TG700
TV SIGNAL GENERATOR PLATFORM
Firmware Installation Instructions

Version 5.62
February 07, 2013

The following describes how to upgrade the TG700 to firmware release
Version 5.62

IMPORTANT NOTE:
---------------
If your instrument contains an HDLG7 module, you must perform
an extra step to complete the firmware upgrade.  Omitting this step
will cause incomplete loading of the FPGA image to the HDLG7.
follow steps 13 and 14 below under "Upgrading the Firmware" carefully.

Equipment Required:
-------------------

The following equipment is required to upgrade the firmware:

* PC with Windows 2000/XP/7 and Ethernet interface installed
* 10 BASE-T Ethernet crossover cable or Ethernet hub
* WINZIP or other .zip file extractor

Downloading the Firmware Package:
---------------------------------

1. To download the latest version of the TG700 firmware, navigate
to the Tektronix Web site: http://www.tektronix.com/software.

2. Enter "TG700" in the "Find by model number or keyword" field.
Click on "GO."

3. Click on the link to Software Upgrade V. 5.62, then download the
archive (zip file) to your PC.

4. Use WINZIP or equivalent extraction software on your PC to
extract the archived files into a folder of your choice.

5. The extracted files should include:
tgUpgrade.exe
tgUpgrade.ini
release_notes.txt
Mainframe folder
Target folder

Upgrading the Firmware:
-----------------------

WARNING: Strict Memory Requirements:

If the mainframe does not have enough memory space, you cannot upgrade the firmware.  If a downloaded frame picture file is stored in the TG700 mainframe, make sure to move the file from the mainframe to your PC before starting the following procedures.  Check the total available memory using the TG7Setup tool.  Total Main board memory size greater than 17 MB and 8 MB of free space is required.

1. Install the TG7Setup tool off of the CD in the software package
received with the TG700 Mainframe.  It can be found in the
TOOLS\TG7Setup directory and is installed by double clicking on the
Setup.exe file and following the instructions.  It can also be
found on www.tektronix.com/software.  Search for TG700 and then
select TG700 Software Tools.

2  Activate TG7Setup by selecting:
Start>All Programs>Tektronix>TG700>TG7Setup.exe

3. Press the front-panel MODULE button to display the TG700 main menu.

4. Use the up or down arrow button to select UTILITY, and then press
the ENTER button.

5. Use the up or down arrow button to select NETWORK.  Press ENTER and
note the IP address.  Enter the IP address that you assigned to
your TG700 in the PC dialog box and click "OK".

6. Select File > Open TG700.

7. Take the two numbers (Free + Used) listed in the Memory box and add
the two numbers together.

8. If the value is less than 17 MB, there is not enough memory to
install the upgrade. This can be fixed by installing the option FP
kit PN: 040-1698-10, which replaces the main board with a 64 MB
version.

9. At the bottom of the window, note the amount of free memory.  If
the free memory is less than 8 Mbyte, the upgrade will not install.
Delete or move to your PC any picture files you may have installed
to free more memory.  Use the TG7Comm tool in the CD tools
directory to move the files.  Then proceed with the upgrade.

Perform the following procedure to upgrade the firmware.
(It is not necessary to uninstall the earlier version of firmware.)

1. Connect the 10BASE-T port on the TG700 rear panel to the Ethernet
port on your PC using an Ethernet crossover cable or Ethernet hub.

2. Power on the TG700 and your PC.

3. Set the network parameters of the TG700.  Refer to Setting Ethernet
Network Parameters in the TG700 User Manual for detailed
information about how to set the parameters.

4. On the PC, double-click the tgUpgrade.exe icon in the folder where
you extracted the downloaded archive. The TG700 Upgrade dialog box
appears.

5. Press the front-panel MODULE button to display the TG700 main menu.

6. Use the up or down arrow button to select UTILITY, and then press
the ENTER button.

7. Use the up or down arrow button to select NETWORK.  Press ENTER and
note the IP address.  Enter the IP address that you assigned to
your TG700 in the PC dialog box and click "OK".

8. If you want to download the signals for the specified module(s),
use the check boxes at the bottom of the dialog box.  Normally, you
need not select any check boxes.  Select the appropriate
checkbox(es) under the following cases:

* ATG7 check box: when you upgrade the TG700 with firmware
version 1.3 or earlier and use the ATG7 module in it.

* AVG7 check box: when you upgrade the TG700 with firmware
version 2.1 or earlier and use the AVG7 module in it.

* AWVG7 check box: when you upgrade the TG700 with firmware
version 2.1 or earlier and use the AWVG7 module in it.

9. Click the Copy button. The PC will start transferring the files
in the upgrade folder to the TG700.

CAUTION: Do not power off the TG700 until file transfer
is complete.  Doing so will prevent the instrument from
starting up normally.

10. When the file transfer is complete, the message box appears.

11. Click the OK button to dismiss the message box.

12. Disconnect the power cable from the power cord connector on
the TG700 rear panel, then connect it again to restart the
instrument.

13. If your TG700 includes an an HDLG7 module, proceed with the
following steps to complete the upgrade.  This process must be
individually run on each installed HDLG7 module.

a. Power on the TG700.

b. Wait for all modules to boot up.

c. When "TG700 : PRESET" appears on the display, press the MODULE
button until the "HDLG7[n] STATUS" display appears.

d. Press and hold the ENTER button until you are prompted by the
"UPDATE FPGA" display.  Press ENTER to upgrade the HDLG7 FPGA
images.  This process takes about 90 seconds.

e. When the "REBOOT" message appears on the display, disconnect
the power to the instrument, then connect it again to restart
the instrument.

Firmware Version Check:
-----------------------

Perform the following procedure to verify that the new firmware
version was properly installed:

1. Press the front-panel MODULE button to display the TG700 main
menu.

2. Use the up or down arrow button to select UTILITY, and then press
the ENTER button.

3. Use the up or down arrow button to select VERSION INFO (F/W).

4. Use the left or right arrow button to select CPU[0].

5. Verify that the new firmware version number 5.62 is displayed in
the menu.

6. If your TG700 contains an HDLG7 module, press the MODULE button
until the HDLG7 status menu appears. Press the ENTER button, then
verify that the FPGA version indicates "4.8."

7. If your TG700 contains an HD3G7 module, press the MODULE button
until the HD3G7 status menu appears. Press the ENTER button, then
verify that the FPGA version indicates "5.F 2012-12-17 12:37".

8. If your TG700 contains an SDI7 module, press the MODULE button
until the SDI7 status menu appears. Press the ENTER button, then
verify that the FPGA version indicates "1.9 2013-1-23 18:32".

By downloading, you agree to the terms and conditions of the Software Download Agreement.

This software applies to: TG700, HD3G7

TG700 Software Download V5.62

Prerequisites

Release Notes

Instructions

Related Product Information