FIRMWARE UPDATE FOR TPS2000 and TPS2000B models

This firmware v11.09 is compatible with all TPS2000 and some TPS2000B models. See release notes for detailed Serial Number information on which TPS2000B models are supported by this firmware. All other TPS2000B models either contain the latest firmware already or will be offered seperate firmware updates on tek.com if updates should become available.

Version: V11.09
Software Type: Firmware

Release Date: Aug 01 2012 - 07:00 am
Part Number: 066139100

Release Notes

Release Notes

TPS2000B/TPS2000  Series Oscilloscope Customer Release Notes
Version:        [11.09 ]
Last revised:   [July 31, 2012]
Product:        TPS2000/TPS2000B

Introduction
-----------------------
Version V11.09 is a firmware upgrade for all TPS2000 and certain TPS2000B
Series oscilloscopes.

Installation Guide
-----------------------
This firmware update is intended to update all TPS2000 and certain TPS2000B
Series oscilloscopes to version v11.09.

Firmware v11.09 is compatible with TPS2000/B instruments with following Serial Numbers:

TPS2012, TPS2012B: all Serial Numbers smaller than C010611
TPS2014, TPS2014B: all Serial Numbers smaller than C010775
TPS2024, TPS2024B: all Serial Numbers smaller than C012109

For all other Serial Numbers please use FW 11.08 or other available firmware versions
greater than v11.09 to obtain optimal display quality.

Serial Number exceptions - we do not recommend to use FW v11.09 with following units.
For these Serial Numbers please use FW 11.08 or other FW greater than v11.09 to obtain optimal display quality:

TPS2012B: C010438, C010439, C010506, C010507, C010508, C010509, C010510
TPS2014B: C010563, C010564, C010642, C010643, C010644, C010645, C010646
TPS2024B: C011278, C011279, C011280, C011281, C011283, C011284, C011285, C011286,
C011287, C011288, C011289, C011290, C011639, C011640, C011641, C011642,
C011643, C011644, C011645, C011646, C011647, C011648, C011847, C011848,
C011849, C011850, C011851, C011852, C011853, C011854, C011855, C012084.

History
-----------------------
V11.09 June 20, 2012
1.Reduce potential of undesirable drift gains with warm-up time of 10 minutes. This firmware sets the
automatic warm-up time duration to 30 minutes, which has shown to significantly remedy the drift
gain problems experienced with shorter warm-ups (TPS2K service menu> utility>service>fact cal>warm up).
2.Eliminate erroneous low battery alert in low/high temperature test when the system is in loop-diagnostic
and the battery remain less than 10%. This firmware eliminates this bug

V11.07 April 25, 2011
The battery system sometimes cannot work and the scope prompts "battery controller failed" when power on.
This firmware fix this bug

V11.06 January 7, 2011
1. Fix the flash of the notice shown in the bottom of the LCD  While users operating the multi-purpose knobs
2. Remove the "Contrast" menu of "Display"
3. Fix the flicker issue
4. Delete the item about "contrast" in HELP

V11.02 October 22, 2010
Initial Release.
1. Support program the bootloader in service menu(Service->Service Diag->Program fwboot.dat).
2. Support 3 new models: TPS2012B, TPS2014B, TPS2024B.

Description
-----------------------
Version V11.09 adds no new features to V11.07.
Version V11.07 adds no new features to V11.06.
Version V11.06 adds no new features to V11.04.
Version V11.04 adds the following features:

1. Support program the bootloader in service menu
2. Support 3 new models: TPS2012B, TPS2014B, TPS2024B.

************
Users who program their own custom application software to
communicate with the TPS2000B/TPS2000 should read the following:

For optimal performance, when programming and communicating to the
instrument the following is recommended:

(1) Be familiar with the programmers guide Status and Events section.

(2) Configure the rear RS232 on instrument, including properties of Baud,
Flow control, EOL string and Parity. Press the UTILITY button.
Select i°Optionsi± option. And press the i°RS232 Setupi± option to configure the
Properties.

(3) Controlling programs should use the *STB query in preference to
the serial poll following a service request (SRQ).

Why:  A serial poll following a service request (SRQ) may cause
communication to hang.

(4) Programs should check for a timeout error after each read.

Why: In rare circumstances, the read following a query may time out.
When a timeout error is observed, it is necessary to re-send the
query and re-read the query response.

======================== END ===========================

By downloading, you agree to the terms and conditions of the Software Download Agreement.

This software applies to: TPS2012B, TPS2014B, TPS2024B, Automotive

FIRMWARE UPDATE FOR TPS2000 and TPS2000B models

Release Notes

Related Product Information