TekExpress HEAC - DPO7000-C-DPO-DSA-MSO70000-B-C - Win XP - Win7 V1.3.6

HDMI Ethernet Audio Back Channel (HEAC) which is part of HDMI 1.4a specifications enables networking of HDMI devices, speeds up signaling between Transmitter and Receiver devices and also provides a faster path for the audio return channel. Option HEAC Compliance Test Software, which meets the HDMI 1.4a HEAC specification, automates a comprehensive range of tests enabling unprecedented efficiency for performing HDMI 1.4a electrical validation.

Comprehensive HDMI 1.4 HEAC solution including test fixtures, DPO7000/C DPO/DSA/MSO70000/B/C Real-Time Oscilloscopes, P7330 or TDP1000 Series Differential Probes, P6245 or TAP1500 Series Active Probes, AWG5000/B, AWG7000/B/C Arbitrary Waveform Generators and DSA8200 Sampling Oscilloscope.

Version: V1.3.6
Software Type: Application

Release Date: Dec 02 2011 - 08:00 am
Part Number: 066116805

Pre-Requisites/System Requirements

Release Notes

Instructions

Prerequisites

Approximately 2 GB of available hard-disk space for the recommended installation, which includes full TekExpress installation and distributed components. Platforms supported: Tektronix DPO/DSA/MSO70000/B/C (DPO/DSA70404/B/C or higher) with Option 2XL, DJA, MTH, PTH OR Tektronix DPO7254/C or DPO7354/C with Option 2XL DJA, MTM, PTM Tektronix AWG5000/B Series (AWG5012, AWG5012B, AWG5014, AWG5014B) with Option 01, 08 OR AWG7000/B/C Series (e.g. AWG7102, AWG7052, AWG7122B, AWG7122C or AWG7062B) with Option 01, 08 Tektronix P7330 for Tektronix DPO/DSA/MSO70000/B/C Series Digital Oscilloscope, Tektronix 016-1884-00 Square Pin Adapter OR Tektronix P6247/P6248/P6330 for Tektronix DPO/DSA70000/B Series or DPO7000 Series, Tektronix 016-1884-00 Square Pin Adapter for P6330, Tektronix TCA-BNC Interface Adapter for DPO/DSA/MSO70000/B/C Series, Tektronix TPA-BNC Interface Adapter for DPO7000/C Series OR TDP1000/1500/3500 for Tektronix DPO7000/C Series Digital Oscilloscope Tektronix P6245 for Tektronix DPO/DSA/MSO70000/B/C Series or DPO7000/C Series (Qty: 2), Tektronix TCA-BNC Interface Adapter for DPO/DSA/MSO70000/B/C Series, Tektronix 196-3463-10 Y-lead Adapter, Tektronix TPA-BNC Interface Adapter for DPO7000/C Series OR Tektronix TAP1500 for Tektronix DPO7000/C Series Digital Oscilloscope(Qty: 2), Tektronix 196-3463-10 Y-lead Adapter.

(1)Tektronix HEAC Fixture KIT - TF-HEAC-TPA-KIT consisting of:
Tektronix Test Fixture TF-HEAC-TPA-MAIN
Tektronix Test Fixture TF-HEAC-TPA-AP
Tektronix Test Fixture TF-HEAC-TPA-CP
Tektronix Test Fixture TF-HEAC-TDR-AR (Qty: 2)
Tektronix Test Fixture TF-HEAC-TDR-CR (Qty: 2)
(174-5746-00) Customer Documentation
(2)Tektronix HDMID Plug Fixture( for Type D and Type D HEAC Testing)TF-HDMID-TPA-P consisting of:
Tektronix Test Fixture TF-HDMID-TPA-P

(3)Tektronix HDMID Receptacle Fixture( for Type D and Type D HEAC Testing) TF-HDMID-TPA-R consisting of:
Tektronix Test Fixture TF-HDMID-TPA-R

(4) Tektronix Fixture TF-HDMI-TPA-CE consisting of: EDID Fixture PCBA EEPROM with HDMI 1.4 Software Ribbon Cable (174-5746-00) Customer Documentation

DSA8200 Sampling Oscilloscope 80E04 TDR-module 80E03 Sampling module 80SSPAR S-Parameter Software.

Release Notes

README.TXT for TekExpress HEAC Ver. 1.3.6 (Build 96)

Contents:
1. Introduction
2. Known Limitations
2.1 TekExpress HEAC application related limitation
2.2 TekExpress HEAC known issues in tests
2.3 Installer related limitation
3. Supported Tests
4. Supported list of equipment and accessories
5. Before you click "RUN"
6. TekExpress HEAC created changes on your system.

Note : During HEAC receiver testing (Ethernet and Audio) it is recommended to
connect the Signal Source (AWG5000/7000/B/C) and Real-time Scope (DPO7000/
DPO/DSA/MSO70000/B/C) using GPIB cable, regular LAN network or using LAN-Cross
cable along with VXI-11 server for TekVisa communication.
=================================================================================
1. Introduction

The Tektronix TekExpress HEAC is an automated test solution for testing
the HEAC compliance for Source and Sink type of HEAC DUTs as per CTS 1.4

The online help file included with software contains the detailed information on
how to use the TekExpress HEAC application. This Readme file contains additional
information for the user.
=================================================================================
2. Known Limitations

2.1 TekExpress HEAC application related limitation
a) User need to have administrative privilege while launching the application
first time.
b) If MS Excel is not installed then reports are not generated after completion
of test.
c) During test execution if user pauses the execution and if user does any
changes in instrument setup then it is important that user restores the
instruments settings to same state before clicking "resume".

2.2 TekExpress HEAC known issues in tests
a) During execution of Differential Signal Characteristics Tests if the signal
quality is not good then the scope may not trigger properly and measurement
values will be invalid and reported in MHT report as #### (improper format)
b) The Pre-recorded waveform files mode is supported for Differential Signal
Receiver Performance Characteristics Tests only.
c) While printing the MHT report, page layout need to be adjusted to obtain
desired level of text and image visibility either by using fit to single page
or by printing report on multiple pages or by using large paper size.
d) During execution of Common mode Receiver/Single mode Receiver, shows type
conflict popup.Re Launch of the application resolves the issue.
e) During execution of Tx CM and SM tests, the IEC stream Verification shows
Memory Exception Error, occurs probably when the signal input is improper.
f) Wrong switch setting for the suite "HEAC Transmitter - Common Mode" in the Online Help document.
Please refer the "NewSwitchSetting.pdf" available at the 'TekExpress HEAC' installed folder.
g) CR00320116: EUT FB :Switch settings as per OLH for CM Transmitter test needs to be checked.
--> Please refer the 'Setup_DUT.pdf' for the switch setting present at 'C:\Program Files (x86)\Tektronix\TekExpress\TekExpress HEAC'.

2.3 Installer related limitation
a) Installation of TekExpress and other software are installed on C: only.
b) User need to have administrative privilege while installing the application
================================================================================
3. Supported Tests
Following HEAC test groups are supported in this version of the application:
Transmitter Differential Signal Characteristics Tests
5.1 Operating DC Voltage
5.2 Jitter MAX
5.3 Rise-Fall Time
5.4 High-Low-Center Level
5.5 Cycle Time
Transmitter CommonMode Signal Characteristics Tests
5.6 Operating DC Voltage
5.7 High-Low Level
5.8 Rise-Fall Time
5.9 Transmit Jitter MAX-Clock Frequency
5.10 IEC 60958-1 Stream Verification
Transmitter SingleMode Signal Characteristics Tests
5.11 Operating DC Voltage
5.12 Signal Amplitude
5.13 Rise-Fall Time
5.14 Transmit Jitter MAX-Clock Frequency
5.15 IEC 60958-1 Stream Verification
Receiver Performance Tests
5.16 Differential Receiver Performance
5.17 CommonMode Receiver Performance
5.18 CommonMode Termination Supply Voltage
5.19 SingleMode Receiver Performance
5.20 SingleMode Termination Supply Voltage
=================================================================================
4. Supported list of equipment and accessories
Real-time oscilloscope : Tektronix DPO/DSA 7000, DPO/DSA/MSO70000/B/C
Signal Source : Tektronix AWG5000/B, AWG7000/B/C
Probe : Tektronix P7330, P7240, P6245/6247/P6248/P6330, TDP1000/1500/2500/3500
Fixture : Tektronix Test Fixture TF-HEAC-TPA-R
Tektronix Test Fixture TF-HEAC-AP-AP Adapter
Tektronix Test Fixture TF-HEAC-AP-CP Adapter
Tektronix Test Fixture TF-HEAC-AP-DP Adapter
Tektronix Test Fixture TF-HEAC-TDR-AR
Tektronix Test Fixture TF-HEAC-TDR-CR
Tektronix Test Fixture TF-HEAC-TDR-AP
Tektronix Test Fixture TF-HEAC-TDR-CP
Tektronix Test Fixture TF-HEAC-MISC
Tektronix Test Fixture TF-HDMID-TPA-P
Tektronix Test Fixture TF-HDMID-TPA-R
=================================================================================
5. Before you click "RUN"
A) Ensure that all the required instruments are properly warmed up, Signal Path
Compensation (SPC) is performed, followed by calibration and cable deskew.
B) Setup before starting tests
B.1 ) For Receiver Performance Tests
- Do the setup connections as per CTS
- Ensure that the patterns are installed on AWG before starting
the tests, copy the patterns from "HEAC Patterns" folder and ensure
that they are on AWG in "C:\HEAC Patterns\Audio" folder as is.
- If HEAC application is running on scope then configure the scope
in "GPIB-Controller" mode.
- If HEAC is running on PC/Laptop then map the X: network drive from
scope to PC/Laptop. (refer steps below for network mapping)
B.2) For Transmitter Signal Characteristics Tests
- Do the setup connections as per CTS
- If HEAC application is running on scope then no additional
steps required.
- If HEAC is running on PC/Laptop then map the X: network drive from
scope to PC/Laptop. (refer steps below for network mapping)

C) Steps for network drive connection
C.1) Background information : After you first launch TekExpress, it creates
the following folders on your computer:

"\My Documents\My TekExpress"

NOTE. Ensure that the "My TekExpress" folder has Full read and write access.
NOTE. If a user with a different Windows login ID launches TekExpress,
a new folder is created under "My documents" of new user.

"\My Documents\My TekExpress\HEAC"
"\My Documents\My TekExpress\HEAC\Untitled Session",

this sub-folder is created every time the "TekExpress HEAC.exe" is launched
and this sub-folder is deleted when you exit application.

CAUTION: Each session has multiple files associated with it. Do not modify
any of the session files and/or folders as this may result in loss
of data or corrupted session files.

The "My TekExpress" folder mentioned above is created as a shared folder
with share name as <domain><user ID>’s My TekExpress
C.2) Steps to map X: from an instrument to PC/Laptop/Scope where TekExpress
is running:
i. Open Windows Explorer.
ii. From the Windows Explorer menu, select Tools > Map Network drive.
iii. Select the Drive letter as X: (if there is any previous connection
on X:, disconnect it first through Tools > Disconnect Network
drive menu of Windows Explorer).
iv. In the Folder field, enter remote My TekExpress folder path
(for example, \\TEKSCOPE-053935\Global John’s My TekExpress )

=================================================================================
6. TekExpress HEAC created changes on your system.
After first launch of "TekExpress HEAC.exe" following changes take place in your
computer.
a) "My TekExpress" folder is created under "My Documents" folder of current user
NOTE: If a user with new login ID launches "TekExpress HEAC.exe",
"My TekExpress" folder is created under "My Documents" of the new user.
b) "HEAC" folder is created under "My TekExpress" folder
c) "Untitled Session" folder is created under "HEAC" folder, note that
everytime "TekExpress HEAC.exe" is launched "Untitled Session" folder is
created under "HEAC" folder and will be deleted after proper termination
of application.
d) If user saves a session in TekExpress HEAC all session files are saved
under "HEAC" folder. Note that each session has multiple files associated
with it and do not tamper with any of the session file(s) and/or folder(s)
this may result in loss of data or corrupted session files.

Instructions

TekExpress HEAC (1.3.6)

Product:  TekExpress HEAC (TEKEXP-HEAC)
Version:  1.3.6
Date   :  2-December-2011

Installation Instructions.

================================================================================

Minimum System Requirements

Processor		Pentium 4/M or equivalent processor.

Operating System	Windows XP Service Pack 2/WIN7.

Memory			512 MB of memory.

Hard Disk		Approximately 2 GB of available hard-disk space for the recommended installation, which includes
full TekExpress installation and distributed components.

Display			Super VGA resolution or higher video adapter (800x600 minimum video resolution for small fonts
or 1024x768 minimum video resolution for large fonts). The application is best viewed at 96 dpi display settings.

Software		•	Microsoft Excel 2002 or above.
•	Microsoft Internet Explorer 6.0 SP1 or later.
•	Microsoft Photo Editor 3.0 or equivalent software for image files viewing.
•	Adobe Reader 6.0 or equivalent software for viewing portable document format (PDF) files.
Other Devices

FREE TRIALS
---------------------
This software download offers 10 free trials. A software security key may be purchased from Tektronix to permanently enable the software application.

================================================================================

Installation

1 TekExpress HEAC

i.  Download HEAC_1_3_6_96.zip, extarct the files to local hard drive.

ii. Run the HEACWebinstaller_1.3.6.96.EXE program. After the installation completes Select "Restart" to reboot the instrument. The local machine must reboot to complete the installation process.

iii. Once the application in successfully installed, user can remove the HEACWebinstaller_1.3.6.96.EXE file from local hard-drive.

iV. TekExpress HEAC shortcut is created on the desktop. Launch  TekExpress HEAC.exe by double-click on it. Once the application launches go to Help on the Menu tab and select About TekExpress. In About TekExPress click on License info,where the user has to enter the license info. This information is also available in the help document provided with this application under section "How To Activate the License"

2 TekExpress HEAC Patterns for Audio Receiver testing

i.  On AWG local hard-drive download HEAC_AudioRX_Patterns_AWG5K.EXE (for AWG5000/B) OR HEAC_AudioRX_Patterns_AWG7K.EXE (for AWG7000/B/C)

ii. Run the downloaded program, this will extract the patterns on AWG local hard-drive. After the installation completes user can remove the above EXE file from local hard-drive.

================================================================================

If for some reason you are unable to download or install this software
please contact the Tektronix Technical Support Center:
Customers calling within the U.S. call 1-800-833-9200 press 3.
Customers calling from outside the U.S. call 503-627-2400.

---End of File---

By downloading, you agree to the terms and conditions of the Software Download Agreement.

This software applies to: DPO7054, DPO7104, DPO7254, DPO70404, DPO70604, DPO70804, DSA70404, DSA70604, DSA70804, AWG7101, AWG7102, AWG7051, AWG7052, AWG5002, AWG5004, AWG5012, AWG5014, DPO7354, DPO71254, DPO71604, DPO72004, DSA71254, DSA71604, DSA72004, AWG7061B, AWG7062B, AWG5002B, AWG5004B, AWG5012B, AWG5014B, AWG7122B, AWG7121B, DPO70404B, DPO70604B, DPO70804B, DPO71254B, DPO71604B, DPO72004B, DSA70404B, DSA70604B, DSA70804B, DSA71254B, DSA71604B, DSA72004B, MSO70404, MSO70604, MSO70804, MSO71254, MSO71604, MSO72004, AWG7122C, MSO71254C, MSO71604C, MSO72004C, DPO71254C, DPO71604C, DPO72004C, DSA71254C, DSA71604C, DSA72004C, DSA70804C, DPO70804C, MSO70804C, DPO7254C, DPO7354C, DPO70404C, DPO70604C, DSA70404C, DSA70604C, MSO70404C, MSO70604C, DPO7054C, DPO7104C

TekExpress HEAC - DPO7000-C-DPO-DSA-MSO70000-B-C - Win XP - Win7 V1.3.6

Prerequisites

Release Notes

Instructions

Related Product Information