WEBMSM CONFIGURATION EDITOR PACKAGE

PC application which allows Configuration of WebMSM for use with MTM400s

Version: V3.0.060.702
Software Type: Application

Release Date: Apr 23 2008 - 07:00 am
Part Number: 063364909

Release Notes

Release Notes

The MTM400A MPEG Transport Stream monitor is the next-generation version of the
MTM400 monitor. This document briefly describes the enhancements implemented
with the MTM400A monitor and lists known operational issues with software
version 3.0. Also included are instructions for upgrading the instrument
firmware using files downloaded from the Tektronix Web site: www.tektronix.com.

Enhancements

The following significant software enhancements have been implemented in the
MTM400A monitor and in version 3.0 of the RUI (Remote User Interface):

- New user-interface with significant usability enhancements, including the
FlexVu display

- Graphical EPG view

- Graphical multiplex bit rate distribution history

- Historic trend graphs for RF and IP metrics

RUI Operational Requirements

Listed below are the system requirements for operating version 3.0 of the RUI:

- Operating System: Windows XP SP2 or Vista

- Intel Pentium 4

- 512 MB of RAM minimum

- Internet Explorer 7

- Sun Java Runtime Environment (JRE), v1.6.0_03

Operational Issue Improvements

The following operational issues existing in the MTM400 monitor have been fixed
or improved in the MTM400A monitor and version 3.0 of the RUI:

- QAMB interface card firmware changed to allow wider frequency range from
88 MHz minimum to 57 MHz minimum (center frequencies).

- Intermittent failure to lock with QAMB2 interface card.

- Intermittent unstable power reading from COFDM interface card fixed.
Stability of COFDM MER reading improved. Poor COFDM MER accuracy at various
frequencies fixed.

- Step in reported MER when COFDM sensitivity is changed.

- In some cases, the MTM400 forgot the IP address during initial IP
address setting if no interface card was installed.

- A spurious PAT/PMT inconsistency error where one of the PMT tables began
in the last byte of a packet.

- Rare crash attempting thumbnails generation on a corrupt stream.

- Failure to offer thumbnails unless a user had purchased at least one
other option.

- Corrected SNMP ObjectID OID, it is now specific to the MTM400.

- Failure to display status of large polling scripts.

- Failure to expose the per PID count of continuity errors via SNMP.

- The MTM400A monitor can now generate thumbnails for a program after it
momentarily switches to encrypted transmission.

- Fixed issue where after an interface card is removed, at the next boot
the unit would erroneously report that it is using the ASI input when it was
using none.

Updating MTM400 Monitors

You can update your existing MTM400 monitor to operate with firmware version 3.0.
If you are not upgrading your firmware to version 3.0 but you require MPEG-2
thumbnail support, you can download and install the MTM400 Thumbnails Support
Package, Tektronix part number 066-0945-01, from the Tektronix Web site: www.
tektronix.com.

Known Issues

The following operational issues are known to exist with the MTM400A monitor.

General Issues

The following are known general issues:

- MTM400 monitors only: This firmware version requires that the MTM400
monitor have BIOS version 2.07. You can upgrade your MTM400 monitor BIOS to
version 2.07 using the upgrade hex file located on the firmware CD. Instructions
describing how to perform the BIOS upgrade are located on the product
documentation CD.

- MTM400A monitors are shipped from the factory in DVB mode and will apply
DVB default limits for tests. When setting up in other regions, the factory
default button on the Stream Configuration screen should be selected to apply
the correct default for the region in use.

- When analyzing complex streams or under suboptimal network conditions,
Timing Graphs have straight lines between bursts of data. This is due to the
client PC not being able to retrieve data before the MTM400A monitor removes it
from its internal buffer.

This issue can be alleviated by setting the MTM400A monitor buffers to a larger
size. To do this, open the Configuration dialog and select the Test Parameters
page. Select the Configuration0 button and type "length" into the search query.
For accuracy and jitter graphs, change the PCR accuracy/jitter history length to
be 256. For PTS graphs, change the PTS Arrival History length to 80.

- The MTM400A monitor may perform a controlled reboot when exposed to a
poor quality RF signal. The workaround is to improve the quality of the signal.

- Spurious warnings can appear in the logs during transport stream
transitions while signal lock is reestablished. There is currently no workaround.

- If an ASI input is removed for several hours, the stream may not be
detected when it is reconnected. If this occurs, reboot the unit.

- The MTM400A supports 10/100 full or half duplex. However, it is
important to use automatic negotiation. Where you have configured switches to
force full duplex or on older hubs that only support half duplex and do not
negotiate, network responses can be slowed by a number of corrupted packets on
the network.

Configuration Files

The following are known issues with using configuration files:

- When validating a configuration file using the "config.xsd" file,
Disabled PID Events may be rejected.

- Copying the current configuration slot can cause a reboot of the MTM400A
monitor when using very complex configuration files. The workaround for this
is to physically disconnect the stream input from the rear of the unit while
copying the slot.

- In some instances, loading a v2.0.7 configuration file will prevent a user
from changing parameters on the new interface cards. Selecting the factory
default will clear this condition.

FlexVu Display

The following are known issues with the FlexVu display:

- If you have more than one MTM400A with different interface cards, the
FlexVu panels will not restore correctly as you switch between them.

- When a FlexVu display is restored, not all graph settings are restored,
for example, trend graph time range.

Gigabit Ethernet (GigE)

The following are known issues with the GigE interface card:

- The GigE interface card may not maintain IGMP sessions where broadcast
membership queries (to 0.0.0.0) are used. The workaround is to use device
specific queries.

- The card cannot ping itself, for example, a ping to 127.0.0.1 will time out.

- The card should typically be set in Auto 10/100/1000 Copper or Optical
mode for most applications. When in 10/100 Forced mode, the network switch must
also be in the link forced mode. If the switch is in Auto Negotiate mode on the
network side, the link may resolve to half duplex.

- The GigE interface cards can recover streams up to the full ASI bitrate and
output these for analysis. However, the MTM400A is rated to 155 Mbps, so, in
some cases, very fast streams from the GigE card will cause the MTM400A to
reboot.

CAUTION. High power, optical small form-factor pluggable (SFP) modules, for
example 1550 nm, must not be looped back without optical attenuation. This
could damage the receiver.

Interface Card Software Version

The MTM400A monitor firmware will interrogate and determine the software
installed on an interface card. If the software on the interface card is
incompatible with the firmware in the MTM400A monitor, the interface card
software will be automatically upgraded; this can take up to 30 minutes. When
the upgrade process starts and finishes, entries are added to the device log.

CAUTION. During the software upgrade, the interface card will not respond.
Do not cycle the power to the MTM400A monitor. In rare instances, this can
damage the interface card firmware.

If you believe that the interface card has failed or is being upgraded, check
the device application log screen, which will show if the card is being
programmed.

RF Interface Cards

The following are known issues with the RF interface cards:

- In some circumstances, the QAM Annex B (Option QB2) BER indicated is
pessimistic.

- The RF LEDs on the rear panel equate to the FEC lock on the Input Card
screen. If new firmware is uploaded, the L-Band interface may not be selected on
start-up. If this occurs, select another interface, and then reselect the L-Band
interface.

- The mechanisms that channel polling employs to prevent false error reporting
mean that in noisy environments there can be a delay before a channel lock
is obtained. In some circumstances, the QAMB interface card is unable to
achieve a satisfactory and stable lock on some channel polls. All observed
instances have corrected themselves on the next poll of that channel.

Service Log

The following are known issues with the Service log:

- On some units, the Service log may display the wrong time and date.

- The Service log runs as a low-priority background test; the accuracy of
the sample periods is approximately one second. No data is lost as the next
sample point contains the data from the missing sample. The output file contains
the actual length of the sample period so that accurate measurements are still
possible.

Templates

The following are known issues with the template feature:

- Services and PIDs can have the constraint "MustBePresent" applied to
them. If an element was present previously, but is no longer present, the
appropriate state is set correctly. However, the other states associated with
the service or PID are remembered from their last recorded values. The correct
behavior should be for these other states to be specified as Unknown.

- The template service name matching function will not work when the unit is
used in implied GB2312 encoding mode.

- After a "reset all" instruction, only the root and leaf nodes return to
a green state.

Thumbnails

The Thumbnail screen will continue to be updated as long as decodable pictures
are being received. Once the stream of pictures stops, the thumbnail display
pauses on the last decoded picture. For example, in encrypted channels that
broadcast unencrypted taster sessions, the last decoded frame of the taster
session will remain on the display.

Specific Test Issues

The following specific test issues are known:

- ISDB-T LDT Tables are not tested.

- Continuity count errors may sometimes be reported incorrectly in tables
that have been involved in previous sync loss events.

- VCT maximum section repetition interval: there is no parameter to alter
the behavior of this test.

- Disabling incorrect table ID on DIT and SIT reserved PIDs is
intermittent; if this becomes an issue, contact Tektronix Technical Support.

Firmware Installation

NOTE. If your instrument requires an upgrade, contact Tektronix Support.

If you have received an upgrade package with hardware and a CD, specific
installation instructions are included in the package documentation. However, if
you have downloaded the latest firmware for the MTM400A monitor from the
Tektronix Web site, the following instructions will guide you through the
process of installing the new firmware.

1. Extract the contents of the downloaded MTM400A firmware zip file to a
directory on your hard drive. The zip file contents include a file with a hex
extension.

2. Start the Internet Explorer Web browser. In the address bar, enter the
IP address or system name of the MTM400 or MTM400A monitor to be upgraded. Allow
the RUI (remote user interface) to start.

3. When the RUI starts, the Hot Spot screen displays two buttons: Device
and Stream. Select the Device button.

4. In the resulting Device view, select the Info button to display the
Device Information screen.

5. MTM400 monitors only: In the Device information screen, note the BIOS
Version. If this is less than 2.07, you need to upgrade the BIOS; the BIOS
upgrade process is described in the Signal Interface Hardware Upgrade
Instructions, Tektronix part number 075-0768-06.

6. Now you must prepare the instrument for the upgrade. If the instrument
is under active control of a management system, for example, to scan multiple
channels, disable the system. If the instrument is just being monitored by a
management system, it does not need to be disabled. However, you should follow
the maintenance procedure for your management system to avoid false alarms.

7. Disconnect the input to the instrument. If you are operating the
instrument remotely, you can do this by selecting the Config button in the
Stream view and changing the Interface to SMPTE (or, if you are already
monitoring SMPTE, change to ASI).

8. Select the Log button in the Device view.

9. In the Log view, select the Clear Log option to clear the device log.

10. Select the Config button in the Device view.

11. In the Configuration view, select Upload Device Firmware... and in the
Device Firmware Upload screen, use the browse button to locate the firmware
files extracted in step one.

12. Select the latest hex file; do not select MTM400 v2.0.6.1 BIOSLDR v2.07.
hex; this is used for the BIOS upgrade process only. Note that the hex file name
is now in the Device Firmware Upload screen.

13. Select the Start button. Depending on line speed, preparing the firmware
file can take between five seconds and five minutes. When the progress bar
reaches the right side, you must wait about three minutes for the code to be
unpacked, tested, and loaded into the permanent memory of the instrument. During
this time, the four Device view buttons will turn gray. When all four buttons
have returned to green, yellow, or red, the upgrade is complete.

14. Close all instances of the Internet Explorer; this will also close the
instrument RUI.

15. Restart Internet Explorer. In the address bar, enter the IP address or
system name of the MTM400 or MTM400A monitor you are upgrading. Allow the
instrument RUI to start. When a security warning appears, accept it. If the
instrument does not have the right version of Java 2 installed, the screens
displayed will instruct you how to install a valid version or even automatically
upgrade you if you have an out of date installation of Java 2.

16. In the Test screen, Device tests, select the Log tab on the right-hand
side. In the Log view, note the upgrade messages. Checkpoint 11 indicates that
the upgrade was successful. Other issues have self-explanatory error messages.
If there was an error, repeat the upgrade procedure before contacting Tektronix
Technical Support. Upgrade firmware is now available within the Connect dialog.

17. Depending on the installed interface card and the firmware version
before the upgrade, the card firmware may need to be upgraded; this will happen
automatically. During the upgrade, the interface card is not available; the user
interface will stop at the initial physical interface detection screen and wait
for the upgrade to complete.

CAUTION. To prevent problems, do not cycle power to the instrument while it is
programming the interface card unless instructed to do so by Tektronix Technical
Support.

18. The upgrade processes are now complete. The instrument inputs can now be
reconnected. Any remote management applications can now be restored.

By downloading, you agree to the terms and conditions of the Software Download Agreement.

This software applies to: WebMSM, WEBMSMF16, WEBMSMF32, WEBMSMF64, WEBMSMFDG, WEBMSMFUL, MPEG-2 / MPEG-4 / H.264