Tektronix Revolutionizes ASIC Prototyping with New Software-Based Debug Solution

Certus™ 2.0 Brings RTL Simulation-Level Visibility to Multi-FPGA Prototypes Eliminating Most Recompiles for Faster, More Efficient Debug

BEAVERTON, Ore., October 30, 2012 - Tektronix, Inc., a leading worldwide provider of test, measurement and monitoring instrumentation, today introduced version 2.0 of its Certus ASIC prototyping debug solution. A suite of software and RTL-based embedded instruments, Certus 2.0 fundamentally changes the ASIC prototyping flow by enabling full RTL-level visibility and making FPGA internal visibility a feature of the prototyping platform. This simulation-level visibility allows engineers to diagnose multiple defects in a day versus a week or more with existing tools.

A major challenge today is that traditional FPGA debug tools are unable to support the requirements of the ASIC prototyping market, particularly as designs have become larger and span multiple FPGA devices. Add the increased complexity of hardware/software interactions and the high-speed operation of most prototypes, and FPGA debug has become a major bottleneck in the ASIC prototyping process. Now, by using Certus 2.0 to pre-instrument up to one hundred thousand signals per FPGA device, designers gain comprehensive RTL-level signal visibility without time consuming synthesis and place and route cycles, allowing complex problems to be pinpointed and resolved quickly.

As a leading supplier of FPGA development and ASIC prototype boards, the Dini Group is at the forefront of ASIC prototyping trends and well acquainted with ASIC prototype debug challenges.

"Proactive debug capability for ASIC prototypes has been a missing ingredient within the FPGA ecosystem," said Mike Dini, founder and president of the Dini Group. "With Certus 2.0 we can instrument the design up front, enabling us to quickly view the full operation of the design during a single debug session and resolve issues in a fraction of the time it takes with traditional tools. What's more it works with all of our existing boards - no need to wait in order to take advantage of all these critical features."

Proactive debug strategy
Certus 2.0 allows designers to automatically instrument all the signals likely to be needed in each of the FPGAs in a multi-FPGA ASIC prototype with a small FPGA LUT impact. This enables a proactive debug and instrumentation strategy, eliminating the need to re-compile the FPGA to debug each new behavior, typically a painful eight to eighteen hour ordeal with traditional tools. Other key capabilities include:

  • Automatic identification and instrumentation of RTL signals based on type and instance name including flip-flops, state machines, interfaces and enumerated types
  • On-chip, at-speed capture and compression of many seconds of data without special external hardware or consuming FPGA I/O resources
  • Advanced on-chip triggering bringing the power of logic analyzer trigger methods to embedded instrumentation
  • Time-correlated capture results across clock domains and multiple FPGAs providing a system-wide view of the entire target design

"Certus 2.0 fundamentally changes the ASIC prototyping flow and dramatically increases debug productivity," said Brad Quinton, chief architect for the embedded instrumentation group at Tektronix. "Because we are now delivering RTL-level visibility of up to a hundred thousand signals spanning the entire design, the debugging use case is comparable to RTL simulation. This enables the direct debugging of hardware and software on the ASIC prototype without going back to simulation, emulation or acceleration platforms, changing the economics of ASIC silicon-based verification."

Certus 2.0 works on any existing commercial or custom ASIC prototyping platform, and does not need special connectors, cables, or external hardware. In addition, Certus 2.0 does not limit the operating speed of the prototype platform.

Tektronix Embedded Instrumentation Solutions
Following the acquisition of Veridae Systems last year, Tektronix Embedded Instrumentation solutions reflect the growing importance of Electronic Design Automation (EDA) software in helping engineers solve difficult instrumentation and debug challenges. As the release of a new version of Certus demonstrates, Tektronix is committed to strategic investment in EDA software-driven debug automation solutions that enable the validation of correct operation and the determination of the root cause of any issues faster in a unified and productive environment.

Availability
The Certus 2.0 ASIC prototyping debug solution is available now and is priced at $19,500 U.S. MSRP for a one year term-based floating license.

Wondering what else Tektronix is up to? Check out the Tektronix Bandwidth Banter blog and stay up to date on the latest news from Tektronix on Twitter and Facebook.

About Tektronix
For more than sixty-five years, engineers have turned to Tektronix for test, measurement and monitoring solutions to solve design challenges, improve productivity and dramatically reduce time to market. Tektronix is a leading supplier of test equipment for engineers focused on electronic design, manufacturing, and advanced technology development. Headquartered in Beaverton, Oregon, Tektronix serves customers worldwide and offers award-winning service and support. Stay on the leading edge at www.tektronix.com.

 

  2012-10-30 07:00:00

Select Service

X

STAY INFORMED: Events & Seminars | Email Newsletter | Follow Tektronix on Twitter Follow Tektronix on Facebook Follow Tektronix on Google+ Follow Tektronix on Youtube

MEMBERSHIP: Create an account for exclusive membership privileges.Login