Tektronix provides comprehensive, integrated tool sets to serve the needs of engineers designing HSIC based embedded systems as well as those validating the physical-layer compliance of HSIC serial devices to the HSIC standard.
The Tektronix MSO/DPO5000, DPO7000C, DPO/DSA/MSO70000C, and DPO/DSA70000D Series oscilloscopes enabled with option HSIC provide automated setup for complete electrical as well as protocol validation of HSIC Device and Host designs.
DPOJET software with HSIC Essentials Setup Library provides a full set of measurements required for HSIC Device and HOST testing. The HSIC Essentials enable Debug Analysis and Characterization to the HSIC specification.
There is no longer a need to be an expert on HSIC testing procedures. Remembering the exact steps to take each measurement is time consuming and often requires going back to the HSIC specifications. HSIC Essentials takes the guesswork out of conducting Device and Host electrical testing. Even if you remember how to use the test equipment, it is common for even the HSIC experienced operators to forget steps in the procedure or to set up the correct parameters, such as applying the correct record length and sampling rates.
Automated DPOJET Setup Library for HSIC provides standard specific details and pre-defined scope settings for each measurement, so the user does not need to be an expert. HSIC Essentials minimizes the setup initialization problems, reduces the complexity of executing HSIC tests and enables you to test designs faster.
HSIC Essentials provide complete set of measurements to be performed across near-end and far end test points, for both device and host validation. Measurements include Signal Quality tests such as Eye mask hits, Strobe Frequency, Packet parameter tests, and Bus timing tests.
HSIC Essentials helps perform step-by-step debugging on failures. HSIC Essentials helps debug faster and discover sources of jitter and signal integrity issues quickly.
The HSIC Essentials Setup Library is highly flexible, and fully-customizable. It allows modifying the measurement settings, scope configurations, limits and other parameters editing and then save the customized setup. For example, when testing a HSIC interconnect bus on a mobilephone design in a temperature chamber setup or when using remote XL cables in the setup, a user can define additional filter files and custom-limits to suit the setup conditions.
The DPOJET Plot feature for HSIC Essentials helps characterize HSIC devices with detailed visual representations. The Result section helps design engineers to look at the test results quickly and clearly. The Report section includes details of each test including Limits, Measured Value, Pass/Fail Results, etc.
The HSIC Essentials application generates thorough HTML/.MHT reports that capture the performance, status, and test results of your device. It also captures eye diagram, oscilloscope waveform screen captures, along with test waveforms optionally. Report generation tool also provide features such as Report Appending, Auto Incrementing Report Naming, Inserting User Comments, Listing Complete Configuration Details, etc. Reports appending feature enables adding results from each of the near-end/far-end test points for both Device and Host designs under test, and create a single-printable-report for sharing the results.
HSIC Essentials will provide protocol decode that can disassemble the HSIC traffic, and decodes according to the protocol, and displayed the decoded data on waveform and event-table, along with red flags on CRC/ECC errors in the decoded data. You can view protocol decode along with time stamps on the decoded data in event-tables.
HSIC packet content search is very useful for isolating the event of interest, but once you’ve captured it and need to analyze the surrounding data, what do you do? In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. With the HSIC protocol decoder application, you can enable the oscilloscope to automatically search through the acquired data for user-defined criteria including serial packet content. Each occurrence is highlighted by a search mark. Rapid navigation between marks is as simple as pressing the Previous (←) and Next (→) buttons on the front panel.
All DPO/DSA/MSO70000C/D models
HSIC Essentials - Electrical Validation and Protocol Decode Solution
Electrical Testing Options
Host and Devices
Signal Quality Tests
Eye Diagram Test, High-Low Voltage, Skew rate, Strobe Frequency, Rx Setup and Hold
Packet Parameter Tests
Inter Packet Gap, Sync Field, EOP, Second Inter Packet Gap
Bus Timing Tests
Suspend, Resume, Reset from Suspend, Reset from high speed
Test Point Selection
Near End and Far End
Report Generation Format
Bus Decoding Options
Analog channels 1-4
Digital channels D0-D15 (MSO5000 and MSO70000C Series only)
Mid-levels for Data and Strobe
Sync, Reset, Suspend, Connect, Resume, Error, Addr, CRC5, CRC16, Data
Hex, Binary, Decimal
Bus and waveforms
Simultaneous display of bus and waveforms
Decoded packet data in a tabular view
Export data to .csv format
Opt.HSIC HSIC Essentials - Electrical Validation and Protocol Decode
New Instrument Orders
MSO/DPO5000/GSA Series (2 GHz and above)
DPO-UP Opt. HSIC
DPO7000C/GSA Series (2.5 GHz and above)
DPO-UP Opt. HSIC
DPO-UP Opt. HSIC
Two sets of TAP1500 or P6245 Probes along with PPM100 Probe Holders are required for HSIC electrical testing as well as protocol decoding.
Please refer to www.tek.com/probes for further information on the recommended models of probes and any necessary probe adapters.
Tektronix offers a range of solutions for USB testing, including HSIC, USB 2.0 and USB 3.0. To see a comprehensive listing, and download the latest resources, visit www.tek.com/USB.
USB solution updates and up-to-date instrument software upgrades are available at www.tek.com/downloads.
|Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.|
Last Modified: 2013-02-26 08:00:00