- Home
- Products
- Oscilloscopes
- Logic Analyzers
- Protocol Analyzers
- Bit Error Rate Testers
- Signal Generators
- Spectrum Analyzers
- Probes and Accessories
- Baseband Video Test Solutions
- MPEG Video Test Solutions
- Video Quality and Service Assurance
- Digital Multimeters
- DC Power Supplies
- Frequency Counters and Timers
- RF Power Meters
- Embedded Instrumentation
- Optical Modulation Analyzer
- Tektronix Communications
- Tektronix Components
- Applications
- Service
- Support
- Purchase
- About Us
- My Account
High-voltage Differential Probes
TMDP0200 • THDP0200 • THDP0100 • P5200A • P5202A • P5205A• P5210A
Features & Benefits
- Bandwidths up to 200 MHz
- Up to 6000 V Differential (DC + pk AC)
- Up to 2300 V Common (RMS)
- Overrange Indicator
- Safety Certified
- Switchable Attenuation
- Switchable Bandwidth Limit
Applications
- Floating Measurements
- Switching Power Supply Design
- Motor Drive Design
- Electronic Ballast Design
- CRT Display Design
- Power Converter Design and Service
- Power Device Evaluation
Safe High-voltage Probe Solutions
Tektronix offers a broad portfolio of high-voltage probing solutions that enable users to safely and accurately make floating measurements.
The THDP0100 and P5210A have the largest differential dynamic range capability from Tektronix, allowing users to safely measure up to ±6000 V. The THDP0100 supports bandwidths up to 100 MHz and slew rates up to 2500 V/ns at 1/1000 gain. These probes are supplied with two sizes of hook tips and have an overrange visual and audible indicator which warns the user when they are exceeding the linear range of the probe.
The THDP0200 and P5205A are active differential probes that are capable of safely measuring differential voltages up to ±1500 V. The probes are effective in making measurements in IGBT circuits such as motor drives and power converters. The THDP0200 supports bandwidths up to 200 MHz and slew rates up to 275 V/ns at 1/250 gain.
The TMDP0200 and P5202A are designed for medium-voltage applications with differential requirements up to ±750 V. These probes have lower attenuation ranges and offer better signal-to-noise ratio.
The P5200A can be used with any oscilloscope and enables users to safely make measurements of floating circuits with their oscilloscope grounded. The P5200A Active Differential Probe converts floating signals to low-voltage ground-referenced signals that can be displayed safely and easily on any ground-referenced oscilloscope.
WARNING: For safe operation, do not use the P5200A High-voltage Differential Probe with oscilloscopes that have floating inputs (isolated inputs), such as the Tektronix TPS2000 and THS3000 Series oscilloscopes. The P5200A High-voltage Differential Probe requires an oscilloscope or other measurement instrument with grounded inputs.
Connectivity Options
The TMDP and THDP Series probes are equipped with the TekVPI® interface which allows smart communication between the oscilloscope and probe. Pushing the probe menu button will launch the probe control menu on the oscilloscope display providing access to all relevant probe settings and controls. These probes are designed to operate on TekVPI® oscilloscopes without requiring the TPA-BNC adapter.
The P52xxA Series probes are equipped with the Tektronix TekProbe® interface which communicates scale information to the oscilloscope. Direct connections can be made to oscilloscopes configured with the TekProbe® interface or to any oscilloscope when used with the 1103 TekProbe® Power Supply.
Characteristics
Probes with the TekVPI® Interface
Characteristic | TMDP0200 | THDP0200 | THDP0100 |
|---|---|---|---|
Attenuation | 25X / 250X | 50X / 500X | 100X / 1000X |
Differential Voltage | 250X: ±750 V 25X: ±75 V | 500X: ±1500 V 50X: ±150 V | 1000X: ±6000 V 100X: ±600 V |
Common Mode Voltage | ±750 V | ±1500 V | ±6000 V |
Maximum Input Voltage-to-Earth | 550 V CAT I 300 V CAT III | 1000 V CAT II 600 V CAT III | 2300 V CAT I 1000 V CAT III |
Bandwidth | 200 MHz | 200 MHz | 100 MHz |
Rise Time | <1.8 ns | <1.8 ns | <3.5 ns |
Slew Rate | <275 V/ns at 1/250 gain | <650 V/ns at 1/500 gain | <2500 V/ns at 1/1000 gain |
Input Impedance at the Probe Tip | 5 MΩ || <2 pF | 10 MΩ || <2 pF | 40 MΩ || <2.5 pF |
Typical CMRR | DC: > –80 dB 1 MHz: > –60 dB 3.2 MHz: > –30 dB 50 MHz: > –26 dB | DC: > –80 dB 1 MHz: > –60 dB 3.2 MHz: > –30 dB 50 MHz: > –26 dB | DC: > –80 dB 1 MHz: > –60 dB 3.2 MHz: > –30 dB 100 MHz: > –26 dB |
Cable Length | 1.5 m | 1.5 m | 1.5 m |
Probes with the TekProbe® Interface
Characteristic | P5200A | P5202A | P5205A | P5210A |
|---|---|---|---|---|
Attenuation | 50X / 500X | 20X / 200X | 50X / 500X | 100X / 1000X |
Differential Voltage | 500X: ±1300 V 50X: ±130 V | 200X: ±640 V 20X: ±64 V | 500X: ±1300 V 50X: ±130 V | 1000X: ±5600 V 100X: ±560 V |
Common Mode Voltage | ±1300 V | ±640 V | ±1300 V | ±5600 V |
Maximum Input Voltage-to-Earth | 1000 V CAT II | 450 V CAT l 300 V CAT ll | 1000 V CAT II | 2300 V CAT l 1000 V CAT III |
Bandwidth | 50 MHz | 100 MHz | 100 MHz | 50 MHz |
Differential Input Impedance | 10 MΩ, 2 pF | 5 MΩ, 2 pF | 10 MΩ, 2 pF | 40 MΩ, 2.5 pF |
Input Impedance between each Input and Ground | 5 MΩ, 4 pF | 2.5 MΩ, 4 pF | 5 MΩ, 4 pF | 20 MΩ, 5 pF |
Typical CMRR | DC: >80 dB 100 kHz: >60 dB 3.2 MHz: >30 dB 50 MHz: >26 dB | DC: >80 dB 100 kHz: >60 dB 3.2 MHz: >40 dB 50 MHz: >30 dB | ||
Cable Length | 1.8 m | |||
1. This is the maximum measurable range between the (+) and (–) input leads of the probe. Beyond these limits, the output could be clipped.2. The maximum common mode voltage and maximum input voltage-to-earth (RMS) are the maximum voltages that each input lead (+/–) can be from ground.
Ordering Information
P5200A, P5202A, and P5205A
High-voltage Differential Probe.
Includes: 2 hook clips (AC280-FL), 2 pincer clips (AC283-FL), 2 alligator clips (AC285-FL), and 2 extension cables (196-3523-00).
Note: Please specify power cord option when ordering.
Power Plug Options (P5200A only)
Option | Description |
|---|---|
Opt. A0 | US power |
Opt. A1 | Euro power |
Opt. A2 | UK power |
Opt. A3 | Australian power |
Opt. A5 | Switzerland power |
Opt. A6 | Japanese power |
Opt. A10 | China power |
Opt. A11 | India power |
Opt. A12 | Brazil power |
TMDP0200 and THDP0200
High-voltage Differential Probes.
Includes: 2 hook clips (AC280-FL), 2 pincer clips (AC283-FL), 2 alligator clips (AC285-FL), 2 extension cables (196-3523-00), 2 test leads (TP175-FL), 1 high-voltage differential browser (THV-BROWSER), and 1 probe holder (TPH1000).
THDP0100 and P5210A
High-voltage Differential Probes.
Includes: 2 probe tips, 2 large hook clips; 2 small hook clips; 2 probe heads (re-order kit number 020-3070-00).
Service Options
Option | Description |
|---|---|
Opt. C3 | Calibration Service 3 Years |
Opt. C5 | Calibration Service 5 Years |
Opt. D1 | Calibration Data Report |
Opt. D3 | Calibration Data Report 3 Years (with Opt. C3) |
Opt. D5 | Calibration Data Report 5 Years (with Opt. C5) |
Opt. R3 | Repair Service 3 Years |
Opt. R5 | Repair Service 5 Years |
196-3523-00: Extender Leads (1.5 m).
AC280-FL: Hook Clips.
AC283-FL: Pincer Clips.
AC285-FL: Alligator Clips.
020-3070-00: Hook Clip Kit.
Probe and Accessory Derating Table (Common Mode, relative to ground, when used with P52xxA Series probes)
Accessory | Description | TMDP0200 / P5202A 450 V CAT I 300 V CAT II | THDP0200 / P5200A / P5205A 1000 V CAT II 600 V CAT III | THDP0100 / P5210A 2300 V CAT I 1000 V CAT III |
|---|---|---|---|---|
196-3523-00 | 2x Extender Leads (1.5 m)
2300 V CAT I 1000 V CAT III | Standard
450 V CAT I 300 V CAT II | Standard
1000 V CAT II 600 V CAT III | Standard
2300 V CAT I 1000 V CAT III |
AC280-FL | 2x Hook Clips
1000 V CAT III 600 V CAT IV | Standard
450 V CAT I 300 V CAT II | Standard
1000 V CAT II 600 V CAT III | Optional
1000 V CAT I 1000 V CAT III |
AC283-FL | 2x Pincer Clips
1000 V CAT III 600 V CAT IV | Standard
450 V CAT I 300 V CAT II | Standard
1000 V CAT II 600 V CAT III | Optional
1000 V CAT I 1000 V CAT III |
AC285-FL | 2x Alligator Clips
1000 V CAT III 600 V CAT IV | Standard
450 V CAT I 300 V CAT II | Standard
1000 V CAT II 600 V CAT III | Optional
1000 V CAT I 1000 V CAT III |
020-3070-00 | Hook Clip Kit
2300 V CAT I 1000 V CAT II | Optional
450 V CAT I 300 V CAT II | Optional
1000 V CAT II 600 V CAT II | Standard
2300 V CAT I 1000 V CAT II |
TP175-FL | 2x Test Leads
1000 V CAT III 600 V CAT IV | Standard (TMDP0200)
550 V CAT I 300 V CAT III | Standard (THDP0200)
1000 V CAT II 600 V CAT III | Optional
2300 V CAT I 1000 V CAT III |
The P52xxA Series probes provide high-voltage differential measurement solutions for any oscilloscope.
 |
 | Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar. |
51W-11195-7
Last Modified: 2011-12-06 08:00:00
- Differential Probe Overview
- Datasheet
- Product Support
