P7630 30 GHz Low Noise TriMode Probe Datasheet

Features & Benefits

• Full 30 GHz Bandwidth to the Probe Tip
• Industry’s Lowest Probe and Scope System Noise
• TriMode™ Probe – One Setup, Three Measurements without Adjusting Probe Tip Connections
• Differential
• Single Ended
• Common Mode

• Connectivity
• Coaxial Adapters
• • 2.92mm
• • SMP
• P7500 Probe Tip Adapter
• • Use P7500 Series TriMode Probe Tips
• Probe automatically detects tips and applies DSP correction filters

• Probe Specific S-parameters
• Unique DSP filters created from data stored in the probe
• TekConnect® Interface – TekConnect Scope/Probe Control and Usability
• Direct Control from Probe Compensation Box or from Scope Menu

Applications

• Examples Include, but are Not Limited To:
• PCI Express Gen3, Serial ATA III, HDMI

Combining TriMode Probing with Low Noise Performance

TriMode Probing enhances productivity by enabling differential, single-ended, and common mode measurements with a single probe setup. Connecting a probe to the device under test can be a time consuming activity, especially if the probe has to be set up differently to make all the necessary measurements. TriMode Probing improves productivity by reducing setup time because only one setup is needed to make the three different types of measurements. Switching between Differential Mode [A-B], Single-Ended Mode [A-Gnd, B-Gnd], and Common Mode [((A+B)/2)-Gnd] is as easy as a press of a button.

Changing Input Modes on the probe is as easy as a press of a button.

As high speed serial data standards increase in speed and signal swings shrink, probes with high bandwidth coupled with low noise and high sensitivity are increasingly important for making accurate measurements.

12 Gb/s 200 mVpp signal measured with a P7630 and P76CA-292C

The DPO/DSA70000D Series Oscilloscopes and the P7630 TriMode probe were designed to deliver the industry’s lowest system noise levels. When used with a P76CA-xxx Coaxial Adapter, the vertical setting on the oscilloscope can be set as low as 3.48 mV/div with a system noise <1 mVrms at 30 GHz bandwidth.

This high sensitivity is critical for being able to make accurate measurements on low amplitude signals. The P7630 probe was designed to deliver superior sensitivity and allow the oscilloscope to directly measure small signals without using a zoom function. Using a zoom function to look at small signals does not change the intrinsic noise floor of the instrument which can make measurements on small signals problematic.

Connectivity

The P7630 probes utilize an interchangeable active tip design built around a custom probe tip interface using high frequency SMPM connectors. The P7630 probe features an Automatic Adapter ID function that recognizes the attached adapter and automatically applies the correct DSP filters. This feature eliminates the risk of manually selecting the wrong tip type and is much more efficient for the user.

Coaxial Adapters

Coaxial adapters enable the probe to act like a differential input channel for the oscilloscope which effectively doubles the number of differential signals a single oscilloscope can measure simultaneously.

P76CA-292

30 GHz Bandwidth Coaxial Adapter with 2.92 mm (F) connectors. This adapter is calibrated at the input connectors and is ideal for use with off the shelf or custom cables. Low skew cable pairs should be used to preserve full bandwidth performance.

P76CA-292C

30 GHz Bandwidth Coaxial Adapter with 2.92 mm (M) connectors and 6” of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with 2.92 mm or SMA output connectors.

P76CA-SMP

30 GHz Bandwidth Coaxial Adapter with SMP (F) connectors and 6” of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with SMP output connectors.

P7500 Series Solder Tip Adapter

P7500 Tip Adapter. This adapter allows the P7630 probe to use existing Tektronix P7500 probe tips. The P7630 probe amplifier has a 50Ω input. When combined with a P7500 probe tip, the probe turns into a passive Z0 style probe with 450Ω of differential input impedance. While Z0 probes can typically present a significant DC load to the device under test, the P7630 will minimize the effect of DC loading through the use of termination voltage adjustment.

P76TA

30 GHz Bandwidth P7500 Tip Adapter. The probe and oscilloscope system will support up to 30 GHz of bandwidth when this adapter is used with the P75PST Performance Solder Tip.

Unique Probe Filters

The P7630 probes contain probe specific S-parameter data. Attaching a P7630 probe to a DSA/DPO70000D oscilloscope transfers this data to the instrument to create unique system DSP filters based on the specific S-parameter data of the oscilloscope and the probe. Creating unique filters based on the specific response of the system is critical as bandwidths increase. At bandwidths of 30 GHz, small variations in the signal path can lead to significant variation in frequency response which cannot be corrected using a nominal DSP filter.